2006-2011 Camry Aurion · Service Manual BRAKE

TEST MODE PROCEDURE

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK

  1. C146002E02
    Release the parking brake.

    NOTICE:
    Before releasing the parking brake, move the shift lever to the P position for safety.

    HINT:
    When the parking brake is applied or the level of the brake fluid is low, the BRAKE warning light comes on.

  2. When the ignition switch on (IG), check that the ABS, VSC (without multi information display), BRAKE warning lights, and master caution, SLIP indicator lights come on for approximately 3 seconds.

    HINT:
    If the skid control ECU stores any DTCs, the ABS, BRAKE, VSC warning (without multi information display) lights, and SLIP indicator light come on.
    If the indicator remains on or does not come on, proceed to troubleshooting for the light circuits listed below.

    Trouble Area
    See procedure
    ABS warning light (Remains on)
    Click here
    ABS warning light (Does not come on)
    Click here
    BRAKE warning light (Remains on)
    Click here
    BRAKE warning light (Does not come on)
    Click here
    VSC warning light (Remains on)
    Click here
    VSC warning light (Does not come on)
    Click here
    SLIP indicator light (Remains on)
    Click here
    SLIP indicator light (Does not come on)
    Click here


SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (INTELLIGENT TESTER)

HINT:
DTCs are stored if any malfunctions are detected during each sensor check.

  1. C139987E01
    Procedure to enter Test Mode.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Check that the steering wheel is centered and move the shift lever to the P position.

    4. Turn the ignition switch on (IG).

    5. C106672
      Set the intelligent tester to Test Mode (select "Signal Check").

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    6. C146077E02
      Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

      HINT:
      If the ABS warning light does not blink, inspect the ABS warning light circuit.

      Trouble Area
      See procedure
      ABS warning light (Remains on)
      Click here
      ABS warning light (Does not come on)
      Click here

  2. Check the sensor signal.

    1. Drive the vehicle straight ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off when the brake pedal is depressed.

      HINT:
      1. The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
      2. The ABS warning light goes off when the sensor signal check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor signal check.

  3. Stop the vehicle.

    NOTICE:
    1. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
    2. If the signal check has not been completed, the ABS warning light will blink while driving and the ABS system will not operate.

  4. Read the DTC(s) by following the tester screen.

    NOTICE:
    1. If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
    2. If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.

    HINT:
    See the list of DTCs (See "DTC of test mode (Signal Check) function").


SENSOR SIGNAL CHECK BY TEST MODE (SIGNAL CHECK) (SST CHECK WIRE)

HINT:
DTCs are stored if any malfunctions are detected during each sensor check.

  1. Procedure to enter Test Mode.

    1. Turn the ignition switch off.

    2. Check that the steering wheel is centered and move the shift lever to the P position.

    3. G022987E07
      Using SST, connect terminals TS and CG of the DLC3.
      SST
      09843-18040  

    4. Turn the ignition switch on (IG).

    5. C146077E01
      Check that the ABS warning light comes on for several seconds and then blinks in Test Mode.

      HINT:
      If the ABS warning light does not blink, inspect the TS and CG terminal circuit, and ABS warning light circuit.

      Trouble Area
      See procedure
      TS and CG terminal circuit
      Click here
      ABS warning light (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here

  2. Check the sensor signal.

    1. Drive the vehicle straight ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off when the brake pedal is depressed.

      HINT:
      1. The sensor check may not be completed if wheelspin occurs, or if the steering wheel is turned during this check.
      2. The ABS warning light goes off when the sensor signal check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor signal check.

  3. Stop the vehicle.

    NOTICE:
    1. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
    2. If the signal check has not been completed, the ABS warning light will blink while driving and the ABS system will not operate.

  4. G022988E01
    Using SST, connect terminals TC and CG of the DLC3.
    SST
    09843-18040  

  5. Count the number of blinks of the ABS warning light.
    C132876E01

    NOTICE:
    1. If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
    2. If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.

    HINT:
    1. If more than one malfunction is detected at the same time, the lowest numbered code will be displayed first.
    2. See the list of DTCs (See "DTC of test mode (Signal Check) function").

  6. After performing the check, disconnect the SST from terminals TS and CG, and TC and CG of the DLC3, and turn the ignition switch off.

  7. Turn the ignition switch on (IG) to cancel the Test Mode.

    HINT:
    1. If the ignition switch is not turned on (IG) after the SST is removed from the DLC3, the previous Test Mode will continue.
    2. If the ignition switch is turned on (IG) with terminals TS and CG shorted, the previous Test Mode will continue.


DTC OF TEST MODE (SIGNAL CHECK) FUNCTION
DTC of Test Mode (Signal Check): 
Code No.
Diagnosis
Trouble Area
C1271/71
Low output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1272/72
Low output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1273/73
Low output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Sensor installation
  3. Speed sensor rotor
C1274/74
Low output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Sensor installation
  3. Speed sensor rotor
C1275/75
Abnormal change in output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Sensor installation
  3. Sensor rotor
C1276/76
Abnormal change in output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Sensor installation
  3. Sensor rotor
C1277/77
Abnormal change in output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Sensor installation
  3. Sensor rotor
C1278/78
Abnormal change in output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Sensor installation
  3. Sensor rotor

HINT:
The codes in this table are output only in Test Mode (signal check).


ENGINE VARIANT LEARNING
  1. Engine variant learning is automatically performed immediately after the Test Mode is entered.
  2. The ABS, VSC, BRAKE, and SLIP indicators come on for 3 seconds after learning.
← TEST MODE PROCEDURE (Jun 2006 – Sep 2006)TEST MODE PROCEDURE (from Jun 2009) →