2006-2011 Camry Aurion · Service Manual BRAKE

C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1330/35, and C1331/36 (Click here).
DTCs from C1273/73 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs from C1273/73 to C1278/78 are output only in the test mode.
DTC No.
DTC Detecting Condition
Trouble Area
C0210/33
C0215/34
When either of the following is detected:
  1. Vehicle speed is more than 40 km/h (25 mph) and pulses are not input for 0.03 sec.
  2. When the vehicle speed has reached 12 km/h (8 mph), after the initial start or restart, a wheel speed of 0 km/h (0 mph) is detected.
  1. Rear speed sensor RH and/or LH
  2. Rear speed sensor circuit RH and/or LH
  3. Rear speed sensor rotor RH and/or LH
  4. Sensor installation
  5. Brake actuator assembly (skid control ECU)
C1332/38
C1333/39
Abnormality in the resistance value of each speed sensor is detected.
  1. Rear speed sensor RH and/or LH
  2. Rear speed sensor circuit RH and/or LH
  3. Sensor installation
C1273/73
C1274/74
Detected only during test mode.
  1. Rear speed sensor
  2. Sensor installation
  3. Sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Rear speed sensor
  2. Sensor installation
  3. Sensor rotor

HINT:
DTC No. C0210/33 and C1332/38 are for the rear speed sensor RH.
DTC No. C0215/34 and C1333/39 are for the rear speed sensor LH.


WIRING DIAGRAM

F040884E28

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select "Data List" and read the value displayed on the intelligent tester (Click here).

    Data List: ABS/TRC/VSC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Wheel speed sensor (RR) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.



NG
Go to step 5
OK


2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Check if test mode (signal check) DTCs are detected (Click here).

    Result:
    Result
    Proceed to
    Test mode (signal check) DTC is not output
    A
    Test mode (signal check) DTC is output
    B



B
Go to step 5
A


3. INSPECT SPEED SENSOR SIGNAL WAVEFORM

  1. C139144E02
    Lift up the vehicle.

  1. Perform the inspection using an oscilloscope.

    1. Disconnect the skid control ECU connector.

    2. Connect the oscilloscope to the rear speed sensor terminals of the skid control ECU.

    3. Check that a waveform is output when the tires are rotated.

      OK:
      The same waveform is output from all the 4 wheels and there is no noise or interference in the waveform.

      HINT:
      1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

    4. Connect the connector.



NG
REPLACE SPEED SENSOR AND SENSOR ROTOR
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
    A
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    B
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
END
A


5. INSPECT SPEED SENSOR INSTALLATION

  1. F010178E07
    Check the rear speed sensor installation.

    OK:
    There is no clearance between the sensor and rear axle carrier.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


6. INSPECT REAR SPEED SENSOR

  1. C113377E01
    Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    g1-2 (RL+) - g1-1 (RL-)
    Below 2.2 kΩ
    g1-2 (RL+) - Body ground
    10 kΩ or higher
    g1-1 (RL-) - Body ground
    10 kΩ or higher
    RH:
    Tester Connection
    Specified Condition
    f1-2 (RR+) - f1-1 (RR-)
    Below 2.2 kΩ
    f1-2 (RR+) - Body ground
    10 kΩ or higher
    f1-1 (RR-) - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE REAR SPEED SENSOR (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO SKID CONTROL SENSOR WIRE)

  1. C139145E03
    Check the harness and connector.
    1. Disconnect the skid control ECU connector and the rear speed sensor connector.

    2. Disconnect the skid control sensor wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      A26-7 (RL+) - g1-2 (RL+)
      Below 1 Ω
      A26-27 (RL-) - g1-1 (RL-)
      Below 1 Ω
      A26-7 (RL+) - Body ground
      10 kΩ or higher
      A26-27 (RL-) - Body ground
      10 kΩ or higher
      RH:
      Tester Connection
      Specified Condition
      A26-29 (RR+) - f1-2 (RR+)
      Below 1 Ω
      A26-8 (RR-) - f1-1 (RR-)
      Below 1 Ω
      A26-29 (RR+) - Body ground
      10 kΩ or higher
      A26-8 (RR-) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU TO SKID CONTROL SENSOR WIRE)
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO REAR SPEED SENSOR)

  1. C113396E05
    Check the harness and connector (skid control sensor wire).
    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      g1-1 - A-1
      Below 1 Ω
      g1-1 - A-2
      10 kΩ or higher
      g1-1 - Body ground
      10 kΩ or higher
      g1-2 - A-2
      Below 1 Ω
      g1-2 - A-1
      10 kΩ or higher
      g1-2 - Body ground
      10 kΩ or higher
      RH:
      Tester Connection
      Specified Condition
      f1-1 - A-1
      Below 1 Ω
      f1-1 - A-2
      10 kΩ or higher
      f1-1 - Body ground
      10 kΩ or higher
      f1-2 - A-2
      Below 1 Ω
      f1-2 - A-1
      10 kΩ or higher
      f1-2 - Body ground
      10 kΩ or higher

    2. Connect the connector.



NG
REPAIR OR REPLACE SKID CONTROL SENSOR WIRE
OK


9. INSPECT SPEED SENSOR SIGNAL WAVEFORM

  1. C139144E02
    Lift up the vehicle.

  1. Perform the inspection using an oscilloscope.

    1. Disconnect the skid control ECU connector.

    2. Connect the oscilloscope to the rear speed sensor terminals of the skid control ECU.

    3. Check that a waveform is output when the tires are rotated.

      OK:
      The same waveform is output from the rear wheels and there is no noise or interference in the waveform.

      HINT:
      1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.

    4. Connect the connector.



NG
CLEAN OR REPLACE SPEED SENSOR AND SENSOR ROTOR
OK


10. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select "Data List" and read the value displayed on the intelligent tester (Click here).

    Data List: ABS/TRC/VSC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Wheel speed sensor (RR) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.

    HINT:
    1. It is suspected that the DTCs were output due to a bad connection of the connector terminal.
    2. If troubleshooting has been carried out according to the "PROBLEM SYMPTOMS TABLE", refer back to the table and proceed to the next step (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


11. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
    A
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    B
    DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
END
A


12. INSPECT SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Remove the rear axle.

  1. Check the rotor.

    OK:
    No scratches, cracks, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Install the rear axle.



NG
CLEAN OR REPLACE SPEED SENSOR ROTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction (+ 7 more codes) (Oct 2006 – May 2009)C0226/21 SFR Solenoid Circuit (+ C0236/22, C0246/23, C0256/24) (Jun 2006 – Sep 2006) →