2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The driver side - side airbag sensor circuit consists of the center airbag sensor assembly, side airbag sensor RH, and rear airbag sensor RH.
If the center airbag sensor assembly receives signals from the side airbag sensor RH and rear airbag sensor RH, it determines whether or not the SRS should be activated.
DTC B1620/21 is recorded when a malfunction is detected in the driver side - side airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1620/21
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the driver side - side airbag sensor circuit for 2 seconds.
  2. Side airbag sensor RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Side airbag sensor RH
  3. Rear airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H045218E10

INSPECTION PROCEDURE


1. CHECK DTC

  1. C123684E06
    Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4. CHECK FLOOR WIRE NO. 2 (OPEN)

  1. C114840E11
    Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5. CHECK FLOOR WIRE NO. 2 (SHORT)

  1. C114841E12
    Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6. CHECK FLOOR WIRE NO. 2 (SHORT TO B+)

  1. C114841E12
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    O7-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7. CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)

  1. C114841E12
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O7-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


8. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR
  1. Check that the part number of the side airbag sensor RH is equal to the number of the other side.

    OK:
    Those numbers are the same.

  1. Connect the connectors to the center airbag sensor assembly and side airbag sensor RH.



NG
Go to step 10
OK


9. CHECK SIDE AIRBAG SENSOR RH

  1. C123685E07
    Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output.
    A
    DTC B1620/21 is output.
    B
    DTC B1625/22 is output.
    C

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



B
Go to step 11

C
REPLACE SIDE AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

10. REPLACE SIDE AIRBAG SENSOR RH

  1. C123684E06
    Replace the side airbag sensor RH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

HINT:
Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



OK
END
NG


11. CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the rear airbag sensor RH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR PROPERLY
OK


12. CHECK CONNECTOR
  1. Disconnect the connector from the rear airbag sensor RH.

  1. Check that the connector (on the rear airbag sensor RH side) is not damaged.

OK:
The connector is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


13. CHECK FLOOR WIRE NO. 2 (OPEN)
  1. Disconnect the connector from the side airbag sensor RH.

  1. C114836E16
    Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


14. CHECK FLOOR WIRE NO. 2 (SHORT)

  1. C114843E12
    Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


15. CHECK FLOOR WIRE NO. 2 (SHORT TO B+)

  1. C114843E12
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    O7-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


16. CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)

  1. C114843E12
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O7-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


17. CHECK REAR AIRBAG SENSOR RH

  1. C142514E04
    Connect the connector to the side airbag sensor RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR RH (Click here)
OK


18. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C142515E05
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the rear airbag sensor RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1615/14 Front Airbag Sensor LH Circuit Malfunction (from Jun 2009)B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009) →