2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The driver side - side airbag sensor circuit consists of the center airbag sensor assembly, side airbag sensor (driver side), and rear airbag sensor (driver side).
If the center airbag sensor assembly receives signals from the side airbag sensor (driver side) and rear airbag sensor (driver side), it determines whether or not the SRS should be activated.
DTC B1620/21 is recorded when a malfunction is detected in the driver side - side airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1620/21
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the driver side - side airbag sensor circuit for 2 seconds.
  2. Side airbag sensor (driver side) malfunction
  3. Rear airbag sensor (driver side) malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Side airbag sensor (driver side)
  4. Rear airbag sensor (driver side)
  5. Center airbag sensor assembly

WIRING DIAGRAM

C123784E01

INSPECTION PROCEDURE


1. CHECK DTC

  1. C123684E03
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor (driver side).

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and side airbag sensor (driver side).

  1. Check that the connectors (on the center airbag sensor assembly side and side airbag sensor (driver side) side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


4. CHECK WIRE HARNESS (OPEN)

  1. C225730E01
    Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


5. CHECK WIRE HARNESS (SHORT)
C114841E16
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - N7-3 (BBL-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - O7-3 (BBR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


6. CHECK WIRE HARNESS (SHORT TO B+)

  1. C114841E16
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N7-3 (BBL-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O7-3 (BBR-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


7. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C114841E16
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    N7-3 (BBL-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O7-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


8. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR
  1. Check that the part number of the side airbag sensor (driver side) is equal to the number of the other side.

    OK:
    Those numbers are the same.

  1. Connect the connectors to the center airbag sensor assembly and side airbag sensor (driver side).



NG
Go to step 10
OK


9. CHECK SIDE AIRBAG SENSOR (DRIVER SIDE)

  1. C123685E03
    Interchange the side airbag sensor (passenger side) with side airbag sensor (driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output.
    A
    DTC B1620/21 is output.
    B
    DTC B1625/22 is output.
    C

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (passenger side) and side airbag sensor (driver side) to their original positions and connect the connectors to them.



B
Go to step 11

C
REPLACE SIDE AIRBAG SENSOR (DRIVER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

10. REPLACE SIDE AIRBAG SENSOR (DRIVER SIDE)

  1. C123684E03
    Replace the side airbag sensor (driver side) (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

HINT:
Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



OK
END
NG


11. CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the rear airbag sensor (driver side).

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR PROPERLY
OK


12. CHECK CONNECTOR
  1. Disconnect the connector from the rear airbag sensor (driver side).

  1. Check that the connector (on the rear airbag sensor (driver side) side) is not damaged.

OK:
The connector is not deformed or damaged.

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


13. CHECK WIRE HARNESS (OPEN)

  1. C145406E01
    Disconnect the connector from the side airbag sensor (driver side).

  1. Using a service wire, connect terminals 2 and 1 of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


14. CHECK WIRE HARNESS (SHORT)

  1. C114843E17
    Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCR-)L
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


15. CHECK WIRE HARNESS (SHORT TO B+)

  1. C114843E17
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N7-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O7-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


16. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C114843E17
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    N7-2 (BCL-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O7-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
REPAIR OR REPLACE FLOOR WIRE NO. 2
A


17. CHECK REAR AIRBAG SENSOR (DRIVER SIDE)

  1. C142514E05
    Connect the connector to the side airbag sensor (driver side).

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR (DRIVER SIDE) (Click here)
OK


18. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C142515E07
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the rear airbag sensor (driver side).

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1620/21 is not output.

    HINT:
    Codes other than DTC B1620/21 may be output at this time, but they are not related to this check.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE RHD)
    B
    NG (except 2GR-FE RHD)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009)B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction (Jun 2006 – Sep 2006) →