2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front passenger side rear airbag sensor circuit consists of the center airbag sensor assembly, rear airbag sensor LH, and side airbag sensor LH.
If the center airbag sensor assembly receives signals from the rear airbag sensor LH and side airbag sensor LH, it determines whether or not the SRS should be activated.
DTC B1635/24 is recorded when a malfunction is detected in the front passenger side rear airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1635/24
  1. The center airbag sensor assembly receives an open circuit signal, a short circuit to ground or a short to B+ signal in the front passenger side rear airbag sensor circuit for 2 seconds.
  2. Side airbag sensor LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Rear airbag sensor LH
  3. Side airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H045218E11

INSPECTION PROCEDURE


1. CHECK DTC

  1. C123701E04
    Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor LH and the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connectors (on the side airbag sensor LH side and rear airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (OPEN)

  1. C114836E15
    Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT TO B+)

  1. C114843E11
    Disconnect the service wire from connector C.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    N7-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C114843E11
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    N7-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7. CONFIRM PART NUMBER OF REAR AIRBAG SENSOR
  1. Check that the part number of the rear airbag sensor LH is equal to the number of the other side.

    OK:
    Those numbers are the same.

  1. Connect the connectors to the side airbag sensor LH and rear airbag sensor LH.



NG
Go to step 9
OK


8. CHECK REAR AIRBAG SENSOR LH

  1. C114844E05
    Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 and B1635/24 are not output.
    A
    DTC B1635/24 is output.
    B
    DTC B1630/23 is output.
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



B
Go to step 10

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

9. REPLACE REAR AIRBAG SENSOR LH
  1. Replace the rear airbag sensor LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



OK
END
NG


10. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR
  1. Check that the part number of the side airbag sensor LH is equal to the number of the other side.

    OK:
    Those numbers are the same.



NG
Go to step 12
OK


11. CHECK SIDE AIRBAG SENSOR LH

  1. C114844E13
    Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 and B1635/24 are not output.
    A
    DTC B1635/24 is output.
    B
    DTC B1630/23 is output.
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



B
Go to step 13

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

12. REPLACE SIDE AIRBAG SENSOR LH
  1. Replace the side airbag sensor LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


13. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C123701E04
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction (from Jun 2009)B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009) →