2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front passenger side rear airbag sensor circuit consists of the center airbag sensor assembly, rear airbag sensor (passenger side), and side airbag sensor (passenger side).
If the center airbag sensor assembly receives signals from the rear airbag sensor (passenger side) and side airbag sensor (passenger side), it determines whether or not the SRS should be activated.
DTC B1635/24 is recorded when a malfunction is detected in the front passenger side rear airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1635/24
  1. The center airbag sensor assembly receives an open circuit signal, a short circuit to ground or a short to B+ signal in the front passenger side rear airbag sensor circuit for 2 seconds.
  2. Side airbag sensor (passenger side) malfunction
  3. Rear airbag sensor (passenger side) malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Rear airbag sensor (passenger side)
  4. Side airbag sensor (passenger side)
  5. Center airbag sensor assembly

WIRING DIAGRAM

C123784E02

INSPECTION PROCEDURE


1. CHECK DTC

  1. C123701E03
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK (Click here)
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor (passenger side) and the rear airbag sensor (passenger side).

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor (passenger side) and rear airbag sensor (passenger side).

  1. Check that the connectors (on the side airbag sensor (passenger side) side and rear airbag sensor (passenger side) side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


4. CHECK WIRE HARNESS (OPEN)

  1. C145406E02
    Using a service wire, connect terminals 2 and 1 of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - O7-2 (BCR-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - N7-2 (BCL-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


5. CHECK WIRE HARNESS (SHORT TO B+)

  1. C114843E18
    Disconnect the service wire from connector C.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O7-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N7-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


6. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C114843E18
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O7-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O7-2 (BCR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N7-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    N7-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


7. CONFIRM PART NUMBER OF REAR AIRBAG SENSOR
  1. Check that the part number of the rear airbag sensor (passenger side) is equal to the number of the other side.

    OK:
    Those numbers are the same.

  1. Connect the connectors to the side airbag sensor (passenger side) and rear airbag sensor (passenger side).



NG
Go to step 9
OK


8. CHECK REAR AIRBAG SENSOR (PASSENGER SIDE)

  1. C114844E05
    Interchange the rear airbag sensor (driver side) with rear airbag sensor (passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 and B1635/24 are not output.
    A
    DTC B1635/24 is output.
    B
    DTC B1630/23 is output.
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the rear airbag sensor (driver side) and rear airbag sensor (passenger side) to their original positions and connect the connectors to them.



B
Go to step 10

C
REPLACE REAR AIRBAG SENSOR (PASSENGER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

9. REPLACE REAR AIRBAG SENSOR (PASSENGER SIDE)

  1. C123701E03
    Replace the rear airbag sensor (passenger side) (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



OK
END
NG


10. CONFIRM PART NUMBER OF SIDE AIRBAG SENSOR
  1. Check that the part number of the side airbag sensor (passenger side) is equal to the number of the other side.

    OK:
    Those numbers are the same.



NG
Go to step 12
OK


11. CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)

  1. C114844E15
    Interchange the side airbag sensor (driver side) with side airbag sensor (passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1630/23 and B1635/24 are not output.
    A
    DTC B1635/24 is output.
    B
    DTC B1630/23 is output.
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (driver side) and side airbag sensor (passenger side) to their original positions and connect the connectors to them.



B
Go to step 13

C
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

12. REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE)
  1. Replace the side airbag sensor (passenger side) (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


13. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C123701E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/24 is not output.

    HINT:
    Codes other than DTC B1635/24 may be output at this time, but they are not related to this check.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE RHD)
    B
    NG (except 2GR-FE RHD)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction (Oct 2006 – May 2009)B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Jun 2006 – Sep 2006) →