2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1830/57 Short in Driver Side Curtain Shield Squib Circuit

Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side curtain shield squib circuit during primary check.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Curtain shield airbag assembly RH (Driver side curtain shield squib)
  3. Center airbag sensor assembly
B1831/57
  1. The center airbag sensor assembly receives an open circuit signal in the driver side curtain shield squib circuit for 2 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Curtain shield airbag assembly RH (Driver side curtain shield squib)
  3. Center airbag sensor assembly
B1832/57
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Curtain shield airbag assembly RH (Driver side curtain shield squib)
  3. Center airbag sensor assembly
B1833/57
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Curtain shield airbag assembly RH (Driver side curtain shield squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C124552E70

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (DRIVER SIDE CURTAIN SHIELD SQUIB)

  1. C123742E06
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag assembly RH.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the curtain shield airbag assembly RH (driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.

SST
09843-18060  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



OK
REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (Click here)
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the wire harness connector (on the curtain shield airbag assembly RH side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


3. CHECK FLOOR WIRE NO. 2 (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

  1. C123744E05
    Disconnect the connectors from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - Body ground
      Ignition switch ON
      Below 1 V
      O16-2 (ICR-) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - O16-2 (ICR-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - Body ground
      Always
      1 MΩ or higher
      O16-2 (ICR-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      O16-1 (ICR+) - O16-2 (ICR-)
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C111695E06
    Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1825/56 Short in Front Passenger Side - Side Squib Circuit (+ B1826/56, B1827/56, B1828/56) (from Jun 2009)B1830/57 Short in Driver Side Curtain Shield Squib Circuit (+ B1831/57, B1832/57, B1833/57) (Oct 2006 – May 2009) →