2006-2011 Camry Aurion · Service Manual RESTRAINTS

B1825/56 Short in Front Passenger Side - Side Squib Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The front passenger side - side squib circuit consists of the center airbag sensor assembly and the front seat side airbag assembly (passenger side).
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side - side squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1825/56
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the front passenger side - side squib circuit during primary check.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Front seat side airbag assembly (Front passenger side - side squib)
  4. Center airbag sensor assembly
B1826/56
  1. The center airbag sensor assembly receives an open circuit signal in the front passenger side - side squib circuit for 2 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Front seat side airbag assembly (Front passenger side - side squib)
  4. Center airbag sensor assembly
B1827/56
  1. The center airbag sensor assembly receives a short circuit to ground signal in the front passenger side - side squib circuit for 0.5 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Front seat side airbag assembly (Front passenger side - side squib)
  4. Center airbag sensor assembly
B1828/56
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the front passenger side - side squib circuit for 0.5 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Front seat side airbag assembly (Front passenger side - side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C123777E02

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY (FRONT PASSENGER SIDE - SIDE SQUIB)

  1. C114818E08
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat side airbag assembly (passenger side).

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the front seat side airbag assembly (front passenger side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.

SST
09843-18060  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828, or 56 is not output.

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828, and 56 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEATBACK ASSEMBLY (PASSENGER SIDE)
NG


2. CHECK WIRE HARNESS (FRONT PASSENGER SIDE - SIDE SQUIB CIRCUIT)

  1. C110406E25
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      for LHD:
      Tester connection
      Condition
      Specified condition
      OY1-1 (SFR+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      OY1-2 (SFR-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      for RHD:
      Tester connection
      Condition
      Specified condition
      NZ1-1 (SFL+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      NZ1-2 (SFL-) - Body ground
      Ignition switch on (IG)
      Below 1 V

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      OY1-1 (SFR+) - OY1-2 (SFR-)
      Always
      Below 1 Ω
      for RHD:
      Tester connection
      Condition
      Specified condition
      NZ1-1 (SFL+) - NZ1-2 (SFL-)
      Always
      Below 1 Ω

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      OY1-1 (SFR+) - Body ground
      Always
      1 MΩ or higher
      OY1-2 (SFR-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester connection
      Condition
      Specified condition
      NZ1-1 (SFL+) - Body ground
      Always
      1 MΩ or higher
      NZ1-2 (SFL-) - Body ground
      Always
      1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester connection
      Condition
      Specified condition
      OY1-1 (SFR+) - OY1-2 (SFR-)
      Always
      1 MΩ or higher
      for RHD:
      Tester connection
      Condition
      Specified condition
      NZ1-1 (SFL+) - NZ1-2 (SFL-)
      Always
      1 MΩ or higher

Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPAIR OR REPLACE FLOOR WIRE NO. 2

C
REPAIR OR REPLACE FLOOR WIRE
A


3. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C114819E01
    Connect the connectors to the front seat side airbag assembly (passenger side) and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828, or 56 is not output.

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828, and 56 may be output at this time, but they are not related to this check.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE RHD)
    B
    NG (except 2GR-FE RHD)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1825/56 Short in Front Passenger Side - Side Squib Circuit (+ B1826/56, B1827/56, B1828/56) (Oct 2006 – May 2009)B1830/57 Short in Driver Side Curtain Shield Squib Circuit (+ B1831/57, B1832/57, B1833/57) (Jun 2006 – Sep 2006) →