B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Also covers:
- B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit
- B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit
- B1908/74 Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The front passenger side pretensioner squib circuit consists of the center airbag sensor assembly and the front seat outer belt assembly (passenger side).This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side pretensioner squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1905/74 |
|
|
| B1906/74 |
|
|
| B1907/74 |
|
|
| B1908/74 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
- After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE PRETENSIONER SQUIB) |
Turn the ignition switch to the LOCK position.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt assembly (passenger side).
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
- CAUTION:
- Never connect a tester to the front seat outer belt assembly (front passenger side pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert straight the SST into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- SST
- 09843-18060
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1905, B1906, B1907, B1908, or 74 is not output.
- HINT:
- Codes other than DTC B1905, B1906, B1907, B1908, and 74 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Check that the wire harness connector (on the front seat outer belt assembly (passenger side) side) is not damaged.
- OK:
- The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK WIRE HARNESS (FRONT PASSENGER SIDE PRETENSIONER SQUIB CIRCUIT) |
Disconnect the connectors from the center airbag sensor assembly.

Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
O8-1 (R+) - Body ground
Ignition switch ON
Below 1 V
O8-2 (R-) - Body ground
Ignition switch ON
Below 1 V
- for RHD:
Tester Connection
Condition
Specified Condition
N8-1 (L+) - Body ground
Ignition switch ON
Below 1 V
N8-2 (L-) - Body ground
Ignition switch ON
Below 1 V
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
Check for an open in the circuit.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O8-1 (R+) - O8-2 (R-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
N8-1 (L+) - N8-2 (L-)
Always
Below 1 Ω
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O8-1 (R+) - Body ground
Always
1 MΩ or higher
O8-2 (R-) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
N8-1 (L+) - Body ground
Always
1 MΩ or higher
N8-2 (L-) - Body ground
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O8-1 (R+) - O8-2 (R-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
N8-1 (L+) - N8-2 (L-)
Always
1 MΩ or higher
- Result:
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the connectors to the front seat outer belt assembly (passenger side) and the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1905, B1906, B1907, B1908, or 74 is not output.
- HINT:
- Codes other than DTC B1905, B1906, B1907, B1908, and 74 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
