2006-2011 Camry Aurion · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

NOTICE:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Seat)

  1. B139103
    Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.


2. REMOVE VERTICAL ADJUSTING HANDLE (for Driver Seat)

  1. B139104
    Remove the 2 screws and vertical adjusting handle.


3. REMOVE RECLINING ADJUSTER RELEASE HANDLE

  1. B139105
    Lift the reclining adjuster release handle.

  1. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT SEAT CUSHION SHIELD

  1. B153813
    Disengage the 2 hooks.

  1. B149580
    Remove the 2 screws.

  1. Disengage the 2 claws and separate the front seat cushion shield.

  1. Disconnect the connector from the front power seat lumbar switch. (w/ lumber support)


5. REMOVE FRONT POWER SEAT LUMBAR SWITCH (w/ Lumbar Support)

  1. B178400
    Remove the 2 screws and front power seat lumbar switch.


6. REMOVE FRONT INNER SEAT CUSHION SHIELD

  1. B148648
    Remove the screw.

  1. Disengage the 2 claws and remove the front inner seat cushion shield.


7. REMOVE FRONT SEAT INNER BELT ASSEMBLY

  1. B152832
    for LHD:

    1. Disengage the 2 hooks.

    2. B151310E01
      Disconnect the connectors and disengage each clamp.

    3. Disconnect the connector. (for Driver seat)

    4. Remove the nut and front seat inner belt assembly.

      B151321E01

  1. B147725
    for RHD:

    1. Disengage the 2 hooks.

    2. B151311E01
      Disconnect the connector and disengage the 2 clamps. (for Driver seat)

    3. Disconnect the connector. (for Driver seat)

    4. Remove the nut and front seat inner belt assembly.

      B151322E01


8. REMOVE FRONT SEAT CUSHION ASSEMBLY

  1. B153814E01
    Disengage the clamp.

  1. Disengage the hooks and remove the front seat cushion assembly.


9. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER

  1. B139121E01
    Remove the 16 hog rings and front separate type seat cushion cover.


10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY

  1. B134682E01
    Remove the 2 screws.

  1. Disconnect the 14 clamps and front separate type seatback cover.

  1. Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.


11. REMOVE FRONT SEAT HEADREST SUPPORT

  1. B134683
    Detach the 2 claws and remove the headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


12. REMOVE FRONT SEATBACK ASSEMBLY (w/o Airbag System)

  1. B153816
    Disengage the 3 hooks.

  1. B153815E01
    Remove the 2 hog rings and front seatback assembly.


13. REMOVE FRONT SEATBACK ASSEMBLY (w/ Airbag System)

  1. B153816
    Disengage the 3 hooks.

  1. B153815E01
    Remove the 2 hog rings.

  1. B153817
    Remove the nut and separate the 2 brackets.

  1. Remove the front seatback assembly.


14. REMOVE FRONT SEPARATE TYPE SEATBACK COVER

  1. B139112E01
    Remove the 10 hog rings and front separate type seatback cover.


15. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

  1. B166770E01
    Disconnect the connector.

  1. Remove the 2 screws and lumbar support adjuster assembly.


16. REMOVE LOWER RECLINING ADJUSTER INSIDE COVER LH
  1. Disconnect the clamp.

  1. B148653
    Remove the screw.

  1. Disengage the claw and remove the lower reclining adjuster inside cover LH.


17. REMOVE LOWER RECLINING ADJUSTER INSIDE COVER RH

  1. B148652
    Remove the screw.

  1. Disengage the claw and remove the lower reclining adjuster inside cover RH.


18. REMOVE UPPER RECLINING ADJUSTER INSIDE COVER LH

  1. B148654
    Remove the screw and upper reclining adjuster inside cover LH.


19. REMOVE UPPER RECLINING ADJUSTER INSIDE COVER RH

  1. B148655
    Remove the screw and upper reclining adjuster inside cover RH.


20. REMOVE FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Remove the 4 bolts and front separate type seatback spring assembly.


21. REMOVE SEAT POSITION SENSOR

  1. C133900
    Disconnect the connector.

  1. Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

  1. C133901
    Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.

← DISASSEMBLY (Jun 2006 – Sep 2006)DISASSEMBLY (from Jun 2009) →