REASSEMBLY
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
- NOTICE:
- Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
| 1.
INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY |
 |
- Install the front separate type seatback spring assembly with the 4 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 2.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Install the upper reclining adjuster inside cover LH with the screw.
| 3.
INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Install the upper reclining adjuster inside cover RH with the screw.
| 4.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover LH with the screw.
| 5.
INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH |
 |
- Engage the claw.
Install the lower reclining adjuster inside cover RH with the screw.
| 6.
INSTALL FRONT SEPARATE TYPE SEATBACK COVER |
 |
- Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 10 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 7.
INSTALL FRONT SEATBACK ASSEMBLY |
 |
- Using hog ring pliers, install the front seatback assembly to the seat frame with 2 new hog rings, and attach the hooks.
- Engage the 3 hooks.
| 8.
INSTALL FRONT SEAT HEADREST SUPPORT |
 |
- Engage the 2 claws to install the front seat headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 9.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY |
 |
- Engage the 2 claws.
Engage the 14 claws.
Install the front seatback board sub-assembly with the 2 screws.
| 10.
INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER |
 |
- Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 16 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 11.
INSTALL FRONT SEAT CUSHION ASSEMBLY |
 |
- Engage the hooks and install the front seat cushion assembly.
| 12.
INSTALL FRONT INNER SEAT CUSHION SHIELD |
 |
- Engage the 2 claws.
Install the front inner seat cushion shield with the screw.
| 13.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
|
 |
- for LHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
- Connect the connectors and engage each clamp.
- Engage the 2 hooks.
- for RHD:
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
| 14.
INSTALL FRONT SEAT CUSHION SHIELD |
 |
- Engage the 2 claws.
Install the front seat cushion shield with the 2 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 15.
INSTALL RECLINING ADJUSTER RELEASE HANDLE |
 |
- Engage the claw to install the reclining adjuster release handle.