2006-2011 Camry Aurion · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.


1. INSTALL FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY

  1. B148636
    Install the front separate type seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

  1. B148654
    Install the upper reclining adjuster inside cover LH with the screw.


3. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

  1. B148655
    Install the upper reclining adjuster inside cover RH with the screw.


4. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH

  1. B148653
    Engage the claw.

  1. Install the lower reclining adjuster inside cover LH with the screw.


5. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

  1. B148652
    Engage the claw.

  1. Install the lower reclining adjuster inside cover RH with the screw.


6. INSTALL FRONT SEPARATE TYPE SEATBACK COVER

  1. B140574E01
    Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


7. INSTALL FRONT SEATBACK ASSEMBLY

  1. B140573E01
    Using hog ring pliers, install the front seatback assembly to the seat frame with 2 new hog rings, and attach the hooks.

  1. B149564
    Engage the 3 hooks.


8. INSTALL FRONT SEAT HEADREST SUPPORT

  1. B134683
    Engage the 2 claws to install the front seat headrest support.

    HINT:
    Use the same procedure for the RH side and LH side.


9. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY

  1. B134682E02
    Engage the 2 claws.

  1. Engage the 14 claws.

  1. Install the front seatback board sub-assembly with the 2 screws.


10. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

  1. B140572E01
    Using hog ring pliers, install the front separate type seat cushion cover to the seat cushion pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


11. INSTALL FRONT SEAT CUSHION ASSEMBLY

  1. B149591E01
    Engage the hooks and install the front seat cushion assembly.


12. INSTALL FRONT INNER SEAT CUSHION SHIELD

  1. B165263
    Engage the 2 claws.

  1. Install the front inner seat cushion shield with the screw.


13. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B147690E01
    for LHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. B151307E02
      Connect the connectors and engage each clamp.

    3. B152832
      Engage the 2 hooks.

  1. B236442E01
    for RHD:

    1. Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connectors and engage each clamp.

    3. Engage the 2 hooks.


14. INSTALL FRONT SEAT CUSHION SHIELD

  1. B148931
    Engage the 2 claws.

  1. Install the front seat cushion shield with the 2 screws.

  1. B165295
    Install the 2 rubber bands on the backside of the front seatback board sub-assembly.


15. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B165262
    Engage the claw to install the reclining adjuster release handle.

← REASSEMBLY (Oct 2006 – May 2009)INSTALLATION (from Oct 2006) →