2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A128081E02
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A137712E01
    Fit the tabs on the bearing retainer into the cutouts on the drive end frame to install the bearing retainer.

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the clutch pulley.

  1. A118367E01
    Install the generator rotor assembly to the drive end frame.


3. INSTALL GENERATOR CLUTCH PULLEY
  1. Temporarily install the clutch pulley onto the rotor shaft.

  1. Mount the generator drive end frame in a vise tightly.

  1. A128069E02
    Confirm SST (A) and (B) shown in the illustration.
    SST
    09820-63021  

  1. A185232E01
    Place SST (A) onto the rotor shaft end.

  1. A185233E01
    Fit SST (B) to the clutch pulley.

  1. A194281E07
    Tighten the pulley by turning SST (B) in the direction shown in the illustration.

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 260 mm (10.24 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.
    3. Check that the drive end frame is secured in the vise tightly.
    4. Hold SST (A) tightly during the operation.

  1. Remove the generator assembly from SST.

  1. Check that the clutch pulley rotates smoothly.

  1. Install a new generator pulley cap to the clutch pulley.

  1. A118365E01
    Place a new generator washer on the generator rotor.


4. INSTALL GENERATOR COIL ASSEMBLY

  1. A128082E06
    Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

  1. A128074
    Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }


5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E17
    While pushing the 2 brushes into the brush holder assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the brush holder hole.

  1. A079316E04
    Install the brush holder assembly to the generator coil with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the brush holder assembly.


6. INSTALL GENERATOR TERMINAL INSULATOR

  1. A128083E01
    Install the terminal insulator to the generator coil.

    NOTICE:
    Pay attention to the installation direction of the terminal insulator.


7. INSTALL GENERATOR REAR END COVER

  1. A128071
    Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }

← REASSEMBLY (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →