2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (for Rear Side)

  1. E135552E01
    Install the No. 1 ultrasonic sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


2. INSTALL NO. 1 ULTRASONIC SENSOR (for Rear Side)

  1. E135368
    Engage the 2 claws and install the No. 1 ultrasonic sensor.

  1. Connect the sensor connector.


3. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (for Rear Side)

  1. E134863E01
    Install the No. 2 ultrasonic sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


4. INSTALL NO. 2 ULTRASONIC SENSOR (for Rear Side)

  1. E135369
    Engage the 2 claws and install the No. 2 ultrasonic sensor.

  1. E135370
    Install the sensor retainer as shown in the illustration.

  1. Connect the sensor connector.


5. INSTALL REAR BUMPER ASSEMBLY (for Rear Side)

  1. without Rear Lower Spoiler:

    1. Engage each No. 2 luggage room wire clamp to the rear bumper reinforcement sub-assembly.

    2. B149446
      Install the grommet.

    3. Connect the connector.

    4. B149450
      Engage each claw.

    5. Install the rear bumper assembly with the 6 screws and 2 clips.

    6. B149449
      Install the 2 rear bumper plates.

  1. with Rear Lower Spoiler:

    1. Engage each No. 2 luggage room wire clamp to the rear bumper reinforcement sub-assembly.

    2. B149446
      Install the grommet.

    3. Connect the connector.

    4. B160685
      Engage each claw.

    5. Install the rear bumper assembly with the 6 screws.

    6. B160686
      Install the 2 rear bumper plates.


6. INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)

  1. B137209
    Install the rear quarter panel mudguard sub-assembly LH with the 3 screws.


7. INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler)

HINT:
Use the same procedure for the RH side and the LH side.


8. INSTALL REAR FLOOR BOARD (w/ Rear Lower Spoiler)

  1. B138885E01
    Install the rear floor board with the 3 nuts, 2 clips and 4 screws.


9. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (for Rear Side)

  1. B136855
    Install the luggage compartment inner trim cover RH with the 2 clips.


10. INSTALL REAR FLOOR FINISH PLATE (for Rear Side)

  1. B136852
    Engage the 7 clips and install the rear floor finish plate.


11. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for Rear Side)

  1. B136879
    Install the 2 No. 1 luggage compartment trim hooks with the 2 screws.


12. INSTALL SPARE WHEEL COVER ASSEMBLY (for Rear Side)

13. INSTALL SPARE WHEEL COVER CLAMP (for Rear Side)

14. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for Rear Side)

15. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (for Front Side)

  1. E134855E01
    Install the No. 1 ultrasonic sensor retainer to the front bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


16. INSTALL NO. 1 ULTRASONIC SENSOR (for Front Side)

  1. E135368
    Engage the 2 claws and install the No. 1 ultrasonic sensor.

  1. Connect the sensor connector.


17. INSTALL FRONT BUMPER ASSEMBLY (for Front Side)

  1. B160029
    Connect each connector.

  1. Engage each claw.

  1. Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B149627
    Install the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.


18. INSTALL COOL AIR INTAKE DUCT SEAL (for Front Side)

  1. B161416
    Install the cool air intake duct seal with the 7 clips.


19. VEHICLE PREPARATION FOR FOG LIGHT AIM ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation to the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the engine coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.
    7. Sit a person of average weight (75 kg, 165 lb) in the driver's seat.
    8. Vehicles with height adjustable suspension should set the vehicle height to the lowest setting prior to adjusting the fog light aim.


20. PREPARATION FOR FOG LIGHT AIMING

  1. E128202E02
    Prepare the vehicle:
    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Create a 25 m (82 ft) distance between the vehicle (fog light bulb center) and the wall.
    4. Make sure that the vehicle is on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen as shown in the illustration.

    E137527E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.

  1. I033423E15
    Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.


21. FOG LIGHT AIMING INSPECTION
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

    NOTICE:
    Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

  1. Start the engine.

  1. Turn on the fog light and check if the cut off line falls within the specified area in the following illustration.

    I041221E20


22. FOG LIGHT AIMING ADJUSTMENT

  1. E128204E01
    Adjust the aim vertically:
    Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

    HINT:
    If it is not possible to correctly adjust fog light aim, check bulb, fog light unit, and fog light unit reflector installation.

← REMOVAL (from Jun 2009)INSTALLATION (from Jun 2009) →