REMOVAL
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE COOL AIR INTAKE DUCT SEAL (for Front Side)
|
 |
- Remove the 7 clips and cool air intake duct seal.
| 2.
REMOVE FRONT BUMPER ASSEMBLY (for Front Side)
|
 |
- Put protective tape around the front bumper assembly.
- Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
- HINT:
- Use the same procedure for the RH side and LH side.
- Remove the 8 screws, 3 clips and 2 radiator grille protectors.
- Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
- HINT:
- Use the same procedure for the RH side and LH side.
w/ Clearance Sonar System:
Disconnect the 2 connectors.
w/ Fog Light:
Disconnect the 2 connectors.
w/ Headlight Cleaner System:
Disconnect the 2 connectors.
- Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.
Remove the front bumper assembly.
| 3.
REMOVE NO. 1 ULTRASONIC SENSOR (for Front Side) |
 |
Disconnect the sensor connector.
- While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 1 ultrasonic sensor.
- HINT:
- The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.
| 4.
REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (for Front Side) |
 |
- Disengage the 2 claws and remove the No. 1 ultrasonic sensor retainer from the front bumper.
| 5.
REMOVE LUGGAGE COMPARTMENT FLOOR MAT (for Rear Side) |
|
| 6.
REMOVE SPARE WHEEL COVER CLAMP (for Rear Side) |
|
| 7.
REMOVE SPARE WHEEL COVER ASSEMBLY (for Rear Side) |
|
| 8.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for Rear Side)
|
 |
- Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.
| 9.
REMOVE REAR FLOOR FINISH PLATE (for Rear Side)
|
 |
- Disengage the 7 clips and remove the rear floor finish plate.
| 10.
REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH (for Rear Side)
|
 |
- Remove the 2 clips and the luggage compartment inner trim cover RH.
| 11.
REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)
|
 |
- Remove the 3 screws and rear quarter panel mudguard sub-assembly LH.
| 12.
REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler) |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 13.
REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler)
|
 |
- Remove the 4 screws, 2 clips, 3 nuts and rear floor board.
| 14.
REMOVE REAR BUMPER ASSEMBLY (for Rear Side)
|
 |
without Rear Lower Spoiler:
- Disconnect the connector.
Disengage the grommet.
- Put protective tape around the rear bumper assembly.
- Using a screwdriver, open the 2 rear bumper plates.
- HINT:
- Tape the screwdriver tip before use.
- Remove the 6 screws and 2 clips.
- Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.
- HINT:
- Use the same procedure for the RH side and LH side.
Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.
Remove the rear bumper assembly.
with Rear Lower Spoiler:
- Disconnect the connector.
Disengage the grommet.
- Put protective tape around the rear bumper assembly.
- Using a screwdriver, open the 2 rear bumper plates.
- HINT:
- Tape the screwdriver tip before use.
- Remove the 6 screws.
- Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.
- HINT:
- Use the same procedure for the RH side and LH side.
Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.
Remove the rear bumper assembly.
| 15.
REMOVE NO. 2 ULTRASONIC SENSOR (for Rear Side) |
 |
Disconnect the sensor connector.
- Remove the sensor retainer as shown in the illustration.
- While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 2 ultrasonic sensor.
- HINT:
- The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.
| 16.
REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (for Rear Side) |
 |
- Disengage the 2 claws and remove the No. 2 ultrasonic sensor retainer from the rear bumper.
| 17.
REMOVE NO. 1 ULTRASONIC SENSOR (for Rear Side) |
 |
Disconnect the sensor connector.
- While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 1 ultrasonic sensor.
- HINT:
- The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.
| 18.
REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (for Rear Side) |
 |
- Disengage the 2 claws and remove the No. 1 ultrasonic sensor retainer from the rear bumper.