2006-2011 Camry Aurion · Service Manual BODY

Power Mirror cannot be Adjusted with Power Mirror Switch

Circuit diagnosis · Vehicles built from Oct 2006

DESCRIPTION

  1. A switch signal of the outer mirror switch is transmitted to the selected outer mirror control ECU. Then, the outer mirror control ECU activates the mirror motor to move the mirror UP, DOWN, RIGHT and LEFT in response to the input.
  2. Mirror control switch and memorized mirror position signals (from the position control ECU & switch (seat ECU)) are sent to the mirror control ECU. The mirror control ECU moves the selected mirror UP, DOWN, LEFT and RIGHT in response to the input.

HINT:
The power mirror control system is a part of the multiplex communication system. This system features shared communication wiring that reduces the wiring complexity of the communication lines. The first step in any repair is to confirm the proper operation of the communication system. Proceed with troubleshooting after the communication has been verified (See the Multiplex Communication System).


WIRING DIAGRAM

B148233E05

INSPECTION PROCEDURE


1. INSPECT OUTER MIRROR SWITCH

  1. B150520
    Remove the outer mirror switch.

  1. Measure the resistance according to the value(s) in the table below when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    2 - 3
    OFF
    10 kΩ or higher
    UP
    225 to 275 Ω
    DOWN
    437 to 503 Ω
    LEFT
    744 to 856 Ω
    RIGHT
    437 to 503 Ω
    1 - 2
    L
    90 to 110 Ω
    R
    10 Ω or less



NG
REPLACE OUTER MIRROR SWITCH
OK


2. CHECK WIRE HARNESS (OUTER MIRROR SWITCH - MAIN BODY ECU RH)

  1. B148250E04
    Disconnect the E85 and E82 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E85-11 (SWM+) - E82-3 (M+)
    Always
    Below 1 Ω
    E85-31 (SWS) - E82-1 (S1)
    Always
    Below 1 Ω
    E85-32 (SWE) - E82-2 (E)
    Always
    Below 1 Ω
    E85-11 (SWM+) - Body ground
    Always
    10 kΩ or higher
    E85-31 (SWS) - Body ground
    Always
    10 kΩ or higher
    E85-32 (SWE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY

  1. B148249E05
    Outer rear view mirror LH:Disconnect the I2 connector.

  1. Apply battery voltage and check operation of the mirror face.

    Standard:
    Measurement Condition
    Mirror Operation
    Battery positive (+) → I2-5 (MV)
    Battery negative (-) → I2-10 (M+)
    Turns upward (A)
    Battery positive (+) → I2-10 (M+)
    Battery negative (-) → I2-5 (MV)
    Turns downward (B)
    Battery positive (+) → I2-4 (MH)
    Battery negative (-) → I2-10 (M+)
    Turns left (C)
    Battery positive (+) → I2-10 (M+)
    Battery negative (-) → I2-4 (MH)
    Turns right (D)

  1. B148248E05
    Outer rear view mirror RH:Disconnect the H3 connector.

  1. Apply battery voltage and check operation of the mirror face.

    Standard:
    Measurement Condition
    Mirror Operation
    Battery positive (+) → H3-5 (MV)
    Battery negative (-) → H3-10 (M+)
    Turns upward (A)
    Battery positive (+) → H3-10 (M+)
    Battery negative (-) → H3-5 (MV)
    Turns downward (B)
    Battery positive (+) → H3-4 (MH)
    Battery negative (-) → H3-10 (M+)
    Turns left (C)
    Battery positive (+) → H3-10 (M+)
    Battery negative (-) → H3-4 (MH)
    Turns right (D)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY
OK

REPLACE OUTER MIRROR CONTROL ECU


← DATA LIST / ACTIVE TEST (from Oct 2006)Power Mirrors do not Return to Memorized Position (from Oct 2006) →