C1249/49 Open in Stop Light Switch Circuit
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
This circuit recognizes brake operation by sending a stop light signal to the skid control ECU.The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light signal input line (STP terminal) or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| C1249/49 |
Stop light switch circuit is open, and stop light switch voltage is 40% or more and less than 67% of the battery voltage. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Check the condition of each related circuit connector before troubleshooting (Click here).
| 1. CHECK STOP LIGHT SWITCH OPERATION (STOP LIGHT SWITCH CIRCUIT) |
Check that the stop lights come on when the brake pedal is depressed and goes off when the brake pedal is released.
- OK:
Pedal Condition
Illumination Condition
Brake pedal depressed
ON
Brake pedal released
OFF
|
|
||||
| OK | |
| 2. INSPECT SKID CONTROL ECU CONNECTOR (STP TERMINAL) |
Disconnect the skid control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A25-20 (STP) - Body ground
Brake pedal depressed
8 to 14 V
A25-20 (STP) - Body ground
Brake pedal released
Below 4.0 V
|
|
||||
| OK | |
| 3. INSPECT SKID CONTROL ECU CONNECTOR (GND TERMINAL CONTINUITY) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Specified Condition
A25-4 (GND1) - Body ground
Below 1 Ω
A25-1 (GND2) - Body ground
Below 1 Ω
Connect the connector.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTC is not output
A
DTC is output (When troubleshooting in accordance with the DTC CHART)
B
DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL VOLTAGE) |
Disconnect the stop light switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A19-2 - Body ground
Always
10 to 14 V
|
|
||||
| OK | |
| 6. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin free
Below 1 Ω
1 - 2
Switch pin pushed in
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH TO SKID CONTROL ECU) |
Disconnect the stop light switch connector and skid control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
A25-20 (STP) - A19-1 (STP)
Below 1 Ω
Connect the connector.
|
|
||||
| OK | ||
| ||
