2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL ANTENNA CORD SUB-ASSEMBLY

HINT:
The double-sided tape and tape are not available as supply parts. If these tapes still have enough adhesion to secure the roof headlining and antenna cord, reuse the tapes. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedures below.

  1. Apply new double-sided tape.

    E141373E02

    1. Remove the double-sided tape from the roof headlining assembly.

    2. Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.

    3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

    4. Peel off the backing sheet from the double-sided tape.

  1. Install the antenna cord to the roof headlining assembly from the front of the vehicle.

    E141372E04

  1. Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

    HINT:
    1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
    2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
    3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.
    4. For the part of the antenna cord near the center of the roof headlining assembly, position the marking tape on the antenna cord within the area indicated by the marking line. Secure the antenna cord to the roof headlining assembly with tape as shown in the illustration.


2. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

  1. B149219
    Pull the roof headlining assembly into the vehicle through the rear left door.

  1. Engage the 4 clips.

  1. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

  1. Install the radio setting condenser to the front pillar RH with the bolt.

  1. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

    B149211E01


3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

  1. B149220
    Pull the roof headlining assembly into the vehicle through the rear left door.

  1. Engage the hook, 4 clips, and 2 fasteners.

  1. Connect the sliding roof drive gear connector.

  1. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

  1. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

  1. Install the radio setting condenser to the front pillar RH with the bolt.

  1. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

    B149212E01


4. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

  1. B147634E01
    Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that the joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


5. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

  1. B132096
    Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

  1. Engage the 4 claws.

  1. B132094
    Engage the 6 claws and install the spot light assembly.


6. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

  1. B139562
    Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

  1. B139563
    Engage the 4 claws.

  1. B139564
    Engage the 4 claws and install the lens cover.


7. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)

  1. with Assist Grip:

    1. B132101
      Assemble the front assist grip sub-assembly as shown in the illustration.

    2. B132102
      Install the front assist grip sub-assembly.


8. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)

  1. B147412
    Assemble the front assist grip sub-assembly as shown in the illustration.

  1. B147408
    Install the front assist grip sub-assembly.


9. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY

HINT:
Use the same procedure for the rear side and the front side.


10. INSTALL VISOR HOLDER
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    B149236

    HINT:
    Use the same procedure for the RH side and the LH side.


11. INSTALL VISOR ASSEMBLY LH

  1. B139565
    Engage the 2 clips and install the visor assembly LH.

  1. B139566
    Engage the 4 claws and install the visor bracket cover.


12. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


13. INSTALL ROOF CONSOLE BOX ASSEMBLY

  1. B132065
    Connect the connectors.

  1. Engage the 2 claws and 2 clips, and then install the roof console box assembly.


14. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

  1. E128843
    Install the rain sensor cover.


15. INSTALL ROOF SIDE INNER GARNISH LH

  1. B132063
    Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.


16. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


17. INSTALL UPPER CENTER PILLAR GARNISH LH

  1. B132060
    Engage the clip.

  1. Install the upper center pillar garnish LH with the bolt.


18. INSTALL LOWER CENTER PILLAR GARNISH LH

  1. B132058
    Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.


19. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B131996
    Install the floor end of the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


20. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

  1. B131995
    Engage the 3 claws and install the lap belt outer anchor cover.


21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132081E01
    Install the front door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


22. INSTALL UPPER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


23. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


25. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132083E01
    Install the front door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


27. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B161239
    Engage the 3 claws to install the rear door inner glass weatherstrip.


28. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B161240
    Engage the claw to install the No. 1 door scuff plate clamp.

  1. Connect each connector.

  1. B136452
    Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

  1. B136451
    Engage the 7 clips to install the rear door trim board to the rear door panel.

  1. Install the 3 screws.


29. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
  1. Connect the connector.

  1. B146098
    Engage the claw and install the courtesy light assembly.


30. INSTALL REAR ASH RECEPTACLE ASSEMBLY LH (w/ Ashtray)

  1. B136442
    Install the rear ash receptacle assembly.


31. INSTALL DOOR ASSIST GRIP COVER LH

  1. B136448
    Engage the 6 claws and install the door assist grip cover.


32. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

  1. B136444
    Engage the 3 claws to install the rear door inside handle bezel plug.


33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B132080E02
    Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


34. INSTALL REAR DOOR SCUFF PLATE LH

  1. B132068
    Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.


35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B132082E01
    Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


36. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


37. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B136577
    Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. B136576
    Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.


38. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

  1. B140589E01
    Attach the 2 front hooks of the seat cushion to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.


39. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

40. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)
  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. B147683
    Temporarily install the front side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. B147684
    Temporarily install the rear side of the front seat assembly with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


41. INSTALL OUTER SEAT TRACK BRACKET COVER RH (for Power Seat)

  1. B147713
    Engage the 4 claws and install the front seat rear outer track bracket cover.


42. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Power Seat)
  1. Engage the 4 claws and install the front seat rear inner track bracket cover.


43. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

44. INSTALL REAR SEAT HEADREST ASSEMBLY

45. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

HINT:
Use the same procedure for the LH side and the RH side.


46. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)

HINT:
Use the same procedure for the LH side and the RH side.


47. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Power Seat)

HINT:
Use the same procedure for the LH side and the RH side.


48. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

49. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connector and clamp.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B166772
    Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B139102
    Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


50. INSTALL OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat)

  1. B148954
    Engage the 4 claws and install the front seat rear outer track bracket cover.


51. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)
  1. Engage the 4 claws and install the front seat rear inner track bracket cover.


52. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

53. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. Engage the 6 clamps and clip and install the No. 2 antenna cord sub-assembly.

    E129185E01


54. INSTALL NO. 2 HEATER TO REGISTER DUCT

  1. B158955
    Install the No. 2 heater to register duct with the 2 screws <H>.


55. INSTALL NO. 3 HEATER TO REGISTER DUCT

  1. B158954
    Install the No. 3 heater to register duct with the 3 screws <H>.


56. INSTALL NO. 1 HEATER TO REGISTER DUCT

  1. B158953
    Install the No. 1 heater to register duct with the 3 screws <H>.


57. INSTALL DEFROSTER NOZZLE ASSEMBLY

  1. B158952
    Install the defroster nozzle assembly with the 3 screws <H>.


58. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT

  1. B158951
    Install the side No. 2 defroster nozzle duct with the screw <H>.


59. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT

  1. B158950
    Install the side No. 1 defroster nozzle duct with the screw <H>.


60. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <J> and 2 nuts <L>.

    B158947E01

  1. Engage each clamp.

  1. Install the bolt <E>.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the 2 passenger airbag bolts <M>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect each connector and install the instrument panel safety pad assembly.

    B158948E01


61. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132564E01
    Connect the connector (yellow colored one).


62. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
  1. Connect the connector.

  1. E129167
    Install the front No. 2 speaker assembly with the 2 bolts.


63. INSTALL INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY

  1. B158945E01
    Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 1 speaker panel sub-assembly.


64. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY

  1. B158943
    Engage the 4 clips and install the instrument panel No. 1 register assembly.


65. INSTALL FRONT PILLAR GARNISH LH

  1. B154714E01
    Remove the protective cover.

  1. B149232E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.


66. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


67. INSTALL INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY

  1. B158944E01
    Engage the 2 guides.

  1. Engage the 6 claws and the 2 clips to install the instrument panel No. 2 speaker panel sub-assembly.


68. INSTALL INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY

  1. B158942
    Engage the 4 clips and install the instrument panel No. 3 register assembly.


69. INSTALL FRONT PILLAR GARNISH RH

  1. B154715E01
    Remove the protective cover.

  1. B149231E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.


70. INSTALL RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver)

  1. E141626
    Connect each connector.

  1. Engage the 4 clips.

  1. Install the radio receiver with heater control panel assembly with the 4 bolts.


71. INSTALL NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
  1. Connect each connector.

  1. E137564
    Engage the 4 clips.

  1. Install the navigation receiver with heater control panel assembly with the 4 bolts.


72. INSTALL CONSOLE BOX ASSEMBLY

  1. B158940
    Engage the 2 claws.

  1. B158939
    Install the 2 bolts <I>.

  1. B158937
    Install the 3 screws <H>.

  1. B158938
    Install the console box assembly with the 3 screws <H>.

  1. B158936E01
    Engage the clamp.


73. INSTALL CONSOLE BOX CARPET

  1. B158935
    Install the console box carpet.


74. INSTALL INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
  1. Connect each connector.

  1. B158961
    Engage the 11 claws and install the instrument panel No. 2 register assembly.


75. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect the connector.

  1. B158962
    Engage the 10 claws and install the upper console panel sub-assembly.


76. INSTALL UPPER CONSOLE PANEL FRONT GARNISH

  1. B158963
    Connect each connector.

  1. Engage the 6 claws and install the upper console panel front garnish.


77. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B158971
    Install the shift lever knob sub-assembly.


78. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Engage the 3 claws and 3 clips.

  1. Install the screw <F> or <N>.

  1. Install the 3 screws <F>.

  1. Install the lower instrument panel sub-assembly with the bolt <D>.


79. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158969E01
    Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover sub-assembly.


80. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


81. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


82. INSTALL COMBINATION METER ASSEMBLY

  1. B158920
    Connect each connector.

  1. Install the combination meter assembly with the 4 screws <B>, <C> or <H>.


83. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B158919E01
    Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel sub-assembly with the 2 clips.


84. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B158917
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


85. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)
  1. Connect the connector.

  1. B158918
    Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.


86. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.

  1. B158916
    Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.


87. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C145843
    Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


88. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C107193
    Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

  1. C107194E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


89. INSTALL STEERING COLUMN COVER

  1. B158914E02
    Engage the claw <a> and install the upper steering column cover.

  1. Engage the 2 claws <b> and install the lower steering column cover.

  1. Install the steering column cover with the 2 screws <A>.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


90. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Install the air hose and connect each connector.

  1. Engage the claw and the 4 clips.

  1. Engage the 2 claws and the DLC3.

  1. Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.


91. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


92. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


93. INSTALL STEERING WHEEL ASSEMBLY

  1. C145840E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


94. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133859E01
    Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C146015E01
    Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


95. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. Engage the claw and install the No. 3 lower steering wheel cover.

    C146016E01


96. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. Engage the claw and install the No. 2 lower steering wheel cover.

    C146017E01


97. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

98. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)

99. INSPECT FRONT SEAT ADJUSTER ASSEMBLY (for Manual Seat)

100. INSPECT STEERING PAD

  1. C146010E01
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


101. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jun 2009)INSTALLATION (from Jun 2009) →