Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD (except 2GR-FE RHD)
REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
1.
PRECAUTION
(Click here )
2.
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here ).
4.
REMOVE LOWER NO. 3 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
5.
REMOVE LOWER NO. 2 STEERING WHEEL COVER
Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.
HINT:
Tape up the screwdriver tip before use.
6.
REMOVE STEERING PAD
Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.
Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.
NOTICE:
When removing the steering pad, do not pull the airbag wire harness.
Disconnect the horn connector from the steering pad.
Disconnect the 2 airbag connectors and remove the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
7.
REMOVE STEERING WHEEL ASSEMBLY
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Disconnect the connectors from the spiral cable.
Using SST, remove the steering wheel assembly.
SST
09950-50013
(09951-05010, 09952-05010, 09953-05020, 09954-05031)
8.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
9.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
10.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
11.
REMOVE STEERING COLUMN COVER
Remove the 2 screws <D>.
Disengage the 2 claws and remove the lower steering column cover.
Disengage the claw and remove the upper steering column cover.
12.
REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.
13.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the No. 1 instrument panel sub-assembly.
14.
REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
Disengage the 3 claws and the 2 clips.
Disconnect the connector and remove the No. 1 instrument panel sub-assembly.
15.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
16.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
Disconnect the connector.
17.
REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Remove the 2 clips.
Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.
18.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws <E>.
Disconnect each connector and remove the combination meter assembly.
19.
REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH side and the LH side.
20.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
21.
REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
22.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the bolt <A>.
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
23.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
24.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
25.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
26.
REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
27.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
28.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)
Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.
29.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.
30.
REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
31.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)
Disengage the 3 claws and the 5 clips.
Disconnect the connector and remove the upper console rear panel sub-assembly.
32.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
33.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
34.
REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
HINT:
Set the shift lever in the D position.
35.
REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 3 clips.
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
36.
REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ CD Player)
Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
37.
REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)
Remove the 4 bolts.
Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.
Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.
38.
REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)
Remove the 4 bolts.
Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver with heater control panel assembly.
39.
REMOVE CONSOLE BOX POCKET
Remove the console box pocket.
40.
REMOVE CONSOLE BOX CARPET
Remove the console box carpet.
41.
REMOVE CONSOLE BOX ASSEMBLY
Remove the 2 screws <F>.
Disengage the clamp.
Remove the 2 bolts <G> and the console box assembly.
42.
REMOVE NO. 2 CONSOLE BOX INSERT FRONT
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
43.
REMOVE NO. 1 CONSOLE BOX INSERT FRONT
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
44.
REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
45.
REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
46.
REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY
Disengage the 4 clips and remove the instrument panel No. 1 register assembly.
47.
REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.
48.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH (for 6 Speakers)
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
49.
REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
50.
REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
Protect the curtain shield airbag assembly. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
51.
REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY
Disengage the 4 clips and remove the instrument panel No. 3 register assembly.
52.
REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.
53.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH (for 6 Speakers)
HINT:
Use the same procedures for the RH side and the LH side (Click here ).
54.
REMOVE NO. 1 DEFROSTER NOZZLE GARNISH
Disengage the 8 clips and the 4 guides.
Disconnect each connector and remove the No. 1 defroster nozzle garnish.
55.
DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY
Disconnect the connector (yellow colored one).
56.
REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disengage each clamp.
Disconnect each connector.
Remove the bolt <J>.
Remove the 2 passenger airbag bolts <C>.
Remove the 2 bolts <H>.
Remove the 2 nuts <I>.
Disengage the 5 claws and remove the instrument panel safety pad assembly.
57.
REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT
Remove the screw <F> and the side No. 1 defroster nozzle duct.
58.
REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT
Remove the screw <F> and the side No. 2 defroster nozzle duct.
59.
REMOVE DEFROSTER NOZZLE ASSEMBLY
Remove the 3 screws <F> and the defroster nozzle assembly.
60.
REMOVE NO. 1 HEATER TO REGISTER DUCT
Remove the 3 screws <F> and the No. 1 heater to register duct.
61.
REMOVE NO. 3 HEATER TO REGISTER DUCT
Remove the 3 screws <F> and the No. 3 heater to register duct.
62.
REMOVE NO. 2 HEATER TO REGISTER DUCT
Remove the 2 screws <F> and the No. 2 heater to register duct.
63.
REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for LHD)
Disengage the 6 clamps and clip and remove the No. 2 antenna cord sub-assembly.
64.
REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (for RHD)
Disengage the 6 clamps and clip and remove the No. 2 antenna cord sub-assembly.
65.
REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)
66.
REMOVE OUTER SEAT TRACK BRACKET COVER LH (for Manual Seat)
Move the front seat assembly fully forward by operating the slide handle.
Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.
HINT:
Tape the screwdriver tip before use.
67.
REMOVE INNER SEAT TRACK BRACKET COVER LH (for Manual Seat)
Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.
HINT:
Tape the screwdriver tip before use.
68.
REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
Move the front seat assembly to the rearmost position by operating the slide handle.
Remove the 2 bolts on the front seat track bracket.
Move the front seat assembly fully forward by operating the slide handle.
Remove the 2 bolts on the rear seat track bracket.
Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.
Disconnect the connectors and clamp.
Remove the front seat assembly.
69.
REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)
70.
REMOVE OUTER SEAT TRACK BRACKET COVER LH (for Power Seat)
for 2AZ-FE: (Click here ) for 2GR-FE: (Click here )
71.
REMOVE INNER SEAT TRACK BRACKET COVER LH (for Power Seat)
for 2AZ-FE: (Click here ) for 2GR-FE: (Click here )
72.
REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
for 2AZ-FE: (Click here ) for 2GR-FE: (Click here )
73.
REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)
74.
REMOVE OUTER SEAT TRACK BRACKET COVER RH (for Manual Seat)
HINT:
Use the same procedure for the RH side and the LH side.
75.
REMOVE INNER SEAT TRACK BRACKET COVER RH (for Manual Seat)
HINT:
Use the same procedure for the RH side and the LH side.
76.
REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)
HINT:
Use the same procedure for the RH side and the LH side.
77.
REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)
78.
REMOVE OUTER SEAT TRACK BRACKET COVER RH (for Power Seat)
HINT:
Use the same procedure for the RH side and the LH side.
79.
REMOVE INNER SEAT TRACK BRACKET COVER RH (for Power Seat)
HINT:
Use the same procedure for the RH side and the LH side.
80.
REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)
HINT:
Use the same procedure for the RH side and the LH side.
81.
REMOVE REAR SEAT HEADREST ASSEMBLY
82.
REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Headrest)
83.
REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)
Detach the 2 front hooks of the seat cushion from the vehicle body.
NOTICE:
Follow the instructions below carefully as the cushion frame can be deformed easily.
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
84.
REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
Remove the 3 rear seat belts from the 3 rear seat shoulder belt guides.
Remove the 4 bolts and rear seatback assembly.
85.
REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
Detach the 2 front hooks of the seat cushion from the vehicle body.
NOTICE:
Follow the instructions below carefully as the cushion frame can be deformed easily.
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
Remove the seat cushion.
86.
REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
Remove the 2 bolts and separate type rear seatback assembly RH.
87.
REMOVE SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Remove the 2 bolts and separate type rear seatback assembly LH.
88.
REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Remove the bolt and rear side seatback assembly LH.
89.
REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
HINT:
Use the same procedures for the RH side and LH side.
90.
REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.
91.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
92.
REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH side and the LH side.
93.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
94.
REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.
95.
REMOVE DOOR ASSIST GRIP COVER LH
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.
96.
REMOVE REAR ASH RECEPTACLE ASSEMBLY LH (w/ Ashtray)
Remove the rear ash receptacle assembly.
97.
REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.
Disconnect the connector.
98.
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Using a clip remover, disengage the 7 clips.
Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.
Disconnect the connector.
Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.
Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.
99.
REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.
100.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
101.
REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
Disengage the 3 claws and remove the lap belt outer anchor cover.
102.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Remove the bolt and disconnect the floor end of the front seat outer belt assembly LH.
103.
REMOVE LOWER CENTER PILLAR GARNISH LH
Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.
104.
REMOVE UPPER CENTER PILLAR GARNISH LH
Remove the bolt.
Disengage the clip and remove the upper center pillar garnish LH.
105.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
106.
REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure for the RH side and the LH side.
107.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
108.
REMOVE LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH side and the LH side.
109.
REMOVE UPPER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH side and the LH side.
110.
REMOVE ROOF SIDE INNER GARNISH LH
Disengage the 5 clips and 2 claws, and remove the roof side inner garnish LH.
111.
REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure for the RH side and the LH side.
112.
REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
Remove the rain sensor cover.
113.
REMOVE ROOF CONSOLE BOX ASSEMBLY
Using a moulding remover, disengage the 2 clips and 2 claws.
Disconnect the connectors and remove the roof console box assembly.
114.
REMOVE VISOR ASSEMBLY LH
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
Disengage the 2 clips and remove the visor assembly LH.
115.
REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
116.
REMOVE VISOR HOLDER
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
HINT:
Use the same procedure for the RH side and the LH side.
117.
REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (for Driver Side)
with Assist Grip:
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
HINT:
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the front assist grip sub-assembly.
118.
REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (for Front Passenger Side)
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
HINT:
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the front assist grip sub-assembly.
119.
REMOVE REAR ASSIST GRIP SUB-ASSEMBLY
HINT:
Use the same procedure for the rear side and the front side.
120.
REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
Using a screwdriver, disengage the 4 claws and remove the lens cover.
HINT:
Tape the screwdriver tip before use.
Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.
HINT:
Tape the screwdriver tip before use.
Disengage the 2 claws <B> and remove the No. 1 room light assembly.
Disconnect the room light connector.
121.
REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
Using a screwdriver, disengage the 2 claws labeled A and 2 claws labeled B from the vehicle body.
HINT:
Tape the screwdriver tip before use.
Using a screwdriver, disengage the 2 claws labeled C and remove the spot light assembly from the headlining.
HINT:
Tape the screwdriver tip before use.
Using a screwdriver, disengage the 4 claws.
HINT:
Tape the screwdriver tip before use.
Pull the light bulb holder in the direction indicated by the arrow in the illustration to detach the claw. Then remove the spot light assembly from the light bulb holder.
122.
REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
Remove the sun roof opening trim moulding.
123.
REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.
Remove the bolt and disconnect the radio setting condenser from the front pillar RH.
Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.
Disconnect the antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.
Disengage the 4 clips.
Remove the roof headlining assembly from the vehicle through the rear left door.
124.
REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.
Remove the bolt and disconnect the radio setting condenser from the front pillar RH.
Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.
Disconnect the antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.
Disconnect the sliding roof drive gear connector.
Disengage the hook, 4 clips, and 2 fasteners.
Remove the roof headlining assembly from the vehicle through the rear left door.
125.
REMOVE ANTENNA CORD SUB-ASSEMBLY
Peel the strips of the tape used to secure the antenna cord only to the extent that allows removal of the antenna cord.
HINT:
Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.
Remove the antenna cord from the roof headlining.