Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE
REMOVAL
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
HINT:
Use the same procedures for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
The procedures listed below are for the No. 3 parking brake cable assembly.
1.
REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY (for Lever Type Parking Brake)
HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY". (Click here )
2.
REMOVE PARKING BRAKE PEDAL ASSEMBLY (for Pedal Type Parking Brake)
HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY". (Click here )
3.
REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Lever Type Parking Brake)
Using a screwdriver, pull up the parking brake lever claw.
Remove the lock nut, the No. 1 wire adjusting nut, and the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.
4.
REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)
Using a screwdriver, pull up the parking brake pedal claw.
Remove the lock nut and the No. 1 wire adjusting nut.
Using needle-nose pliers, remove the clip and the No. 1 parking brake cable from the parking brake pedal assembly.
5.
SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)
Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
6.
SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)
Separate the No. 2 parking brake cable assembly from the parking brake equalizer.
7.
REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)
Slide the rubber boot as shown in the illustration.
Remove the No. 4 parking brake cable assembly from the parking brake equalizer as shown in the illustration.
8.
REMOVE CENTER EXHAUST PIPE ASSEMBLY
Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.
Remove the gasket from the front exhaust pipe.
9.
REMOVE NO. 2 FRONT FLOOR HEAT LOWER INSULATOR
Remove the 3 nuts and the No. 2 front floor heat lower insulator.
11.
SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for LHD)
Remove the 2 bolts and separate the rear disc brake caliper assembly.
HINT:
Do not disconnect the flexible hose from the disc brake caliper assembly.
12.
REMOVE REAR DISC (for LHD)
Release the parking brake and put matchmarks on the rear disc and the axle hub.
Remove the rear disc.
HINT:
If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.
13.
REMOVE PARKING BRAKE SHOE RETURN TENSION NO. 1 SPRING (for LHD)
Using needle-nose pliers, remove the 2 parking brake shoe return tension No. 1 springs.
14.
REMOVE PARKING BRAKE SHOE STRUT (for LHD)
Remove the parking brake shoe strut and the parking brake shoe strut compression spring.
15.
REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY (for LHD)
Release the claw of the parking brake shoe hold down spring No. 1 cup.
Remove the No. 1 parking brake shoe assembly as shown in the illustration.
Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 1 pin.
16.
REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for LHD)
Remove the parking brake shoe adjusting screw set.
Remove the parking brake shoe return tension No. 2 spring.
17.
REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY (for LHD)
Release the claw of the parking brake shoe hold down spring No. 1 cup.
Remove the No. 2 parking brake shoe assembly as shown in the illustration.
Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 2 pin.
Using needle-nose pliers, disconnect the No. 3 parking brake cable assembly from the parking brake shoe lever.
NOTICE:
Be careful not to damage the No. 3 parking brake cable assembly.
18.
DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for LHD)
Remove the 2 bolts and disconnect the No. 3 parking brake cable assembly from the backing plate.
19.
DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for RHD)
Using needle-nose pliers, remove the clip.
Turn and disconnect the No. 3 parking brake cable assembly as shown in the illustration.
20.
REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY
Using needle-nose pliers, remove the clip from the No. 3 parking brake cable assembly.
Remove 3 bolts (A), bolt (B), and nut (C), and disengage each claw.
Remove the No. 3 parking brake cable assembly from the body.
Remove the parking brake cable clamp.