REMOVAL
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
- HINT:
- Use the same procedure for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
- The procedures listed below are for the No. 3 parking brake cable assembly.
| 1.
REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY |
 |
- HINT:
- Refer to the procedures up to "REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY". (Click here)
| 2.
REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD) |
 |
- HINT:
- Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)". (Click here)
| 3.
REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD) |
 |
- HINT:
- Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)". (Click here)
| 4.
REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Lever Type Parking Brake)
|
 |
- Using a screwdriver, pull up the parking brake lever claw.
- Remove the lock nut, the No. 1 wire adjusting nut, and the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.
| 5.
REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)
|
 |
- Using a screwdriver, pull up the parking brake pedal claw.
- Remove the lock nut and the No. 1 wire adjusting nut.
- Using needle-nose pliers, remove the clip and the No. 1 parking brake cable from the parking brake pedal assembly.
| 6.
SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake) |
 |
- Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
| 7.
SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake) |
 |
- Separate the No. 2 parking brake cable assembly from the parking brake equalizer.
| 8.
REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake) |
 |
- Slide the rubber boot as shown in the illustration.
- Remove the No. 4 parking brake cable assembly from the parking brake equalizer as shown in the illustration.
| 9.
REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)
|
 |
Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.


Remove the gasket from the front exhaust pipe.
| 10.
REMOVE EXHAUST TAIL PIPE ASSEMBLY (for 2GR-FE)
|
 |
Remove the 4 nuts and 2 exhaust tail pipes.


Remove the 2 gaskets from the exhaust tail pipes.
| 11.
REMOVE EXHAUST CENTER PIPE ASSEMBLY (for 2GR-FE)
|
 |
Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.


Remove the gasket from the exhaust front pipe assembly.
| 12.
REMOVE NO. 2 FRONT FLOOR HEAT LOWER INSULATOR (for 2AZ-FE) |
 |
- Remove the 3 nuts and the No. 2 front floor heat lower insulator.
| 13.
DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
|
 |
- Using needle-nose pliers, remove the clip.
Turn and disconnect the No. 3 parking brake cable assembly as shown in the illustration.
| 14.
REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY |
 |
- Using needle-nose pliers, remove the clip from the No. 3 parking brake cable assembly.
Remove 3 bolts (A), bolt (B), and nut (C), and disengage each claw.


Remove the No. 3 parking brake cable assembly from the body.
- Remove the parking brake cable clamp.