2006-2011 Camry Aurion · Service Manual BRAKE

C1249/49 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This circuit recognizes brake operation by sending a stop light signal to the skid control ECU.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light signal input line (STP terminal) or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC No.
DTC Detection Condition
Trouble Area
C1249/49
When either of the following is detected:
  1. After the ignition switch is turned on (IG), the STP terminal voltage of the ECU is 40% to 67% of its supplied voltage for 0.5 seconds.
  2. When STP signal is OFF (release the brake pedal), the pressure sensor value exceeds 725 bar for 1 second.
  1. Stop light switch
  2. Stop light switch circuit
  3. Brake actuator assembly (skid control ECU)

WIRING DIAGRAM

C213414E02

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION (STOP LIGHT SWITCH CIRCUIT)
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Pedal Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
Go to step 5
OK


2. INSPECT SKID CONTROL ECU (STP1 TERMINAL)

  1. C136493E17
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A26-30 (STP1) - Body ground
    Brake pedal depressed
    8 to 14 V
    A26-30 (STP1) - Body ground
    Brake pedal released
    Below 4.0 V



NG
Go to step 7
OK


3. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)

  1. C136493E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-4 (GND1) - Body ground
    Below 1 Ω
    A26-1 (GND2) - Body ground
    Below 1 Ω

  1. Connect the connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C

    HINT:
    It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE TERMINAL VOLTAGE)

  1. C205914E05
    Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A79-2 - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH POWER SOURCE CIRCUIT)
OK


6. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. C205985E07
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    free
    Below 1 Ω
    1 - 2
    pushed in
    10 kΩ or higher

  1. Connect the connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH TO SKID CONTROL ECU)

  1. C205979E04
    Disconnect the stop light switch connector and skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-30 (STP1) - A79-1(STP1)
    Below 1 Ω

  1. Connect the connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH TO SKID CONTROL ECU)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT CIRCUIT)


← C1249/49 Open in Stop Light Switch Circuit (Oct 2006 – May 2009)C1288/88 ECU Version Miss Match (Jun 2006 – Sep 2006) →