DISASSEMBLY
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE NO. 1 ULTRASONIC SENSOR (w/ Clearance Sonar System)
|
 |
Disconnect the sensor connector.
- While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 1 ultrasonic sensor.
- HINT:
- The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.
| 2.
REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)
|
 |
- Disengage the 2 claws and remove the No. 1 ultrasonic sensor retainer from the rear bumper.
| 3.
REMOVE NO. 2 ULTRASONIC SENSOR (w/ Clearance Sonar System)
|
 |
Disconnect the sensor connector.
- Remove the sensor retainer as shown in the illustration.
- While pushing down on the lever with a finger to release the claw, disengage the claw on the other side to remove the No. 2 ultrasonic sensor.
- HINT:
- The type of the claw on the top and bottom of the sensor are different. Observe the claws carefully before attempting to remove the sensor.
| 4.
REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)
|
 |
- Disengage the 2 claws and remove the No. 2 ultrasonic sensor retainer from the rear bumper.
| 5.
REMOVE NO. 2 LUGGAGE ROOM WIRE (w/ Clearance Sonar System) |
|
| 6.
REMOVE REAR LOWER SPOILER (w/ Rear Lower Spoiler) |
 |
Remove the 2 screws, 4 nuts and 16 clips.


| 7.
REMOVE REAR BUMPER EXTENSION LH (w/ Rear Lower Spoiler) |
 |
- Remove the 2 nuts and rear bumper extension LH.
| 8.
REMOVE REAR BUMPER EXTENSION RH (w/ Rear Lower Spoiler) |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 9.
REMOVE REAR BUMPER PLATE LH |
|
| 10.
REMOVE REAR BUMPER PLATE RH |
|
| 11.
REMOVE REFLEX REFLECTOR ASSEMBLY LH |
 |
- Remove the screw and reflex reflector assembly LH.
| 12.
REMOVE REFLEX REFLECTOR ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 13.
REMOVE REAR BUMPER SIDE SUPPORT LH |
 |
- Remove the 2 screws.
Disengage the claw and 2 guides, and remove the rear bumper side support LH.
| 14.
REMOVE REAR BUMPER SIDE SUPPORT RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 15.
REMOVE REAR BUMPER SIDE RETAINER LH |
 |
- Remove the screw.
Disengage the claw and guide, and remove the rear bumper side retainer LH.
| 16.
REMOVE REAR BUMPER SIDE RETAINER RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 17.
REMOVE WHEEL HOUSE REINFORCEMENT LH |
 |
- Remove the nut and wheel house reinforcement LH.
| 18.
REMOVE WHEEL HOUSE REINFORCEMENT RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 19.
REMOVE REAR BUMPER REINFORCEMENT SUB-ASSEMBLY |
 |
- Remove the 6 nuts and rear bumper reinforcement sub-assembly.