REASSEMBLY
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY |
 |
- Install the rear bumper reinforcement sub-assembly with the 6 nuts.
-
Torque:
- 68 N*m{
693 kgf*cm
, 50 ft.*lbf
}
| 2.
INSTALL WHEEL HOUSE REINFORCEMENT LH |
 |
- Install the wheel house reinforcement LH with the nut.
| 3.
INSTALL WHEEL HOUSE REINFORCEMENT RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 4.
INSTALL REAR BUMPER SIDE RETAINER LH |
 |
- Engage the claw and guide, and install the rear bumper side retainer LH.
Install the 2 screws.
| 5.
INSTALL REAR BUMPER SIDE RETAINER RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 6.
INSTALL REAR BUMPER SIDE SUPPORT LH |
 |
- Engage the claw and 2 guides, and install the rear bumper side support LH.
Install the 2 screws.
| 7.
INSTALL REAR BUMPER SIDE SUPPORT RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 8.
INSTALL REFLEX REFLECTOR ASSEMBLY LH |
 |
- Install the reflex reflector assembly LH with the screw.
| 9.
INSTALL REFLEX REFLECTOR ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 10.
INSTALL REAR BUMPER PLATE LH |
|
| 11.
INSTALL REAR BUMPER PLATE RH |
|
| 12.
INSTALL REAR BUMPER EXTENSION LH (w/ Rear Lower Spoiler) |
 |
- Install the rear bumper extension LH with the 2 nuts.
| 13.
INSTALL REAR BUMPER EXTENSION RH (w/ Rear Lower Spoiler) |
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 14.
INSTALL REAR LOWER SPOILER (w/ Rear Lower Spoiler) |
 |
Engage the 16 claws and install the rear lower spoiler.


Install the 16 clips, 4 nuts and 2 screws.
| 15.
INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ Clearance Sonar System) |
|
| 16.
INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)
|
 |
- Install the No. 2 ultrasonic sensor retainer to the rear bumper.
- NOTICE:
- Do not damage the bumper with the snap when installing the retainer.
- HINT:
- When installing the retainer, align the keyhole and snap as shown in the illustration.
| 17.
INSTALL NO. 2 ULTRASONIC SENSOR (w/ Clearance Sonar System)
|
 |
- Engage the 2 claws and install the No. 2 ultrasonic sensor.
- Install the sensor retainer as shown in the illustration.
Connect the sensor connector.
| 18.
INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Clearance Sonar System)
|
 |
- Install the No. 1 ultrasonic sensor retainer to the rear bumper.
- NOTICE:
- Do not damage the bumper with the snap when installing the retainer.
- HINT:
- When installing the retainer, align the keyhole and snap as shown in the illustration.
| 19.
INSTALL NO. 1 ULTRASONIC SENSOR (w/ Clearance Sonar System)
|
 |
- Engage the 2 claws and install the No. 1 ultrasonic sensor.
Connect the sensor connector.