REMOVAL
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 2.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
|
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 3.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 4.
REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 5.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle)
|
 |
- Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.
| 6.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY |
|
| 7.
REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)
|
 |
- Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
- Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
| 8.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)
|
 |
- Disengage the 3 claws and the 5 clips.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 9.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
|
| 10.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)
|
 |
- Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 11.
REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
|
 |
- Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
- HINT:
- Set the shift lever in the D position.
| 12.
REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY
|
 |
- Apply protective tape to the areas shown in the illustration.
- Using a moulding remover, disengage the 3 clips.
- Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
| 13.
REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY
|
 |
- Remove the 4 bolts.
Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.
Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.
| 14.
REMOVE RADIO NO. 1 BRACKET (w/o Radio Receiver)
|
 |
- Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 1 bracket.
| 15.
REMOVE RADIO NO. 2 BRACKET (w/o Radio Receiver)
|
 |
- Remove the 2 bolts, 3 screws, radio receiver panel, and radio No. 2 bracket.
| 16.
REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver) |
 |
- Remove the air conditioning control assembly as shown in the illustration.