2006-2011 Camry Aurion · Service Manual BODY

B2343 Position Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Oct 2006

Versions by build date: Jun 2006 – Sep 2006 from Oct 2006

DESCRIPTION

This DTC is output when the sliding roof drive gear sub-assembly (sliding roof control ECU) has not been initialized.
DTC No.
DTC Detection Condition
Trouble Area
B2343
Sliding roof drive gear sub-assembly (sliding roof control ECU) has not been initialized
  1. Sliding roof drive gear sub-assembly (sliding roof control ECU)
  2. Roof console box assembly (sliding roof control switch)
  3. Wire harness

WIRING DIAGRAM

Refer to DTC B2341 (Click here).

INSPECTION PROCEDURE


1. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
  1. Check that the sliding roof drive gear sub-assembly can be initialized (Click here).

    OK:
    Sliding roof drive gear sub-assembly can be initialized.



NG
Go to step 3
OK


2. CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the OPEN, CLOSE, UP, and DOWN switches (Click here).

    OK:
    Auto operation operates normally with OPEN, CLOSE, UP, and DOWN switches.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END

3. CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - OVERHEAD JUNCTION BLOCK)

  1. B131169E03
    Disconnect the Q12 and Q6 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q6-3 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q6-2 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q6-4 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q6-1 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q6-5 (UP)
    Always
    Below 1 Ω
    Q6-1 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q6-2 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q6-3 (GND) - Body ground
    Always
    Below 1 Ω
    Q6-4 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q6-5 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF CONTROL SWITCH)

  1. B131165E02
    Remove the roof console box assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    Q6-1 (CLS) - Q6-3 (GND)
    CLOSE
    Below 100 Ω
    Q6-2 (OPN) - Q6-3 (GND)
    OPEN
    Below 100 Ω
    Q6-4 (DOWN) - Q6-3 (GND)
    DOWN
    Below 100 Ω
    Q6-5 (UP) - Q6-3 (GND)
    UP
    Below 100 Ω
    Q6-1 (CLS) - Q6-3 (GND)
    OPEN
    1 kΩ or higher
    Q6-2 (OPN) - Q6-3 (GND)
    CLOSE
    1 kΩ or higher
    Q6-4 (DOWN) - Q6-3 (GND)
    UP
    1 kΩ or higher
    Q6-5 (UP) - Q6-3 (GND)
    DOWN
    1 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)


← B2343 Position Initialization Incomplete (Jun 2006 – Sep 2006)Sliding Roof Control Switch Circuit (from Jun 2006) →