2006-2011 Camry Aurion · Service Manual ENGINE

P1660 VSV for AICVS Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The air cleaner is equipped with two inlets, one of which is opened or closed by the Air Intake Control Valve (AICV). This system reduces intake noise and increases engine power at low to high engine speed range.
When the engine is operating in the low-to-mid speed range, this control operates the AICV to close one of the air cleaner inlets. When the engine speed is more than 3,600 rpm and the opening angle of the throttle valve is more than 60°, the ECM activates the VSV and opens the AICV.
A061332E03
DTC No.
Detection Condition
Trouble Area
P1660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. Voltage of terminal ACIS of the ECM is low when the VSV is OFF
  2. The engine has been started
  1. Open or short in air intake control valve circuit
  2. Air intake control valve
  3. ECM

WIRING DIAGRAM

A141057E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSV FOR AICV)

  1. A067588E07
    Turn the ignition switch on (IG) and turn the intelligent tester ON.

  1. Select the following menu items: Powertrain / Engine / Active Test / Active the VSV for ACIS and operate the VSV for AICV.

  1. Check the operation of the VSV when the VSV is operated by the intelligent tester.

    Standard:
    Tester Operation
    Specified Condition
    VSV is ON
    Air from port E flows out through port F
    VSV is OFF
    Air from port E flows out through the air filter



OK
Go to step 4
NG


2. CHECK VSV ASSEMBLY (FOR AICV)
  1. Inspect the intake air control valve assembly (Click here).



NG
REPLACE INTAKE AIR CONTROL VALVE ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (VSV FOR AICV - EFI MAIN RELAY)

  1. A137083E08
    Check the wire harness between the VSV for AICV connector and the ECM connector.
    1. Disconnect the A53 VSV for AICV connector.

    2. Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

    3. Measure the resistance between the terminals of the wire harness side connectors and body ground.

      Standard resistance (Check for open):
      RHD:
      Tester Connection
      Specified Condition
      VSV for AICV (A53-2) - AICV (A24-4)
      Below 1 Ω
      LHD:
      Tester Connection
      Specified Condition
      VSV for AICV (A53-2) - AICV (A55-4)
      Below 1 Ω


      Standard resistance (Check for short):
      RHD:
      Tester Connection
      Specified Condition
      VSV for AICV (A53-2) or AICV (A24-4) - Body ground
      10 kΩ or higher
      LHD:
      Tester Connection
      Specified Condition
      VSV for AICV (A53-2) or AICV (A55-4) - Body ground
      10 kΩ or higher

  1. Check the EFI No. 3 fuse.

    1. Remove the EFI No. 3 fuse from the engine room R/ B.

    2. Measure the resistance of the EFI No. 3 fuse.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI No. 3 fuse.

  1. Check the wire harness between the VSV for AICV and the EFI relay.

    1. Remove the engine room junction block from the engine room R/B.

    2. Measure the resistance between the terminals of the wire harness side connectors.

      Standard resistance:
      Check for open:
      Tester Connection
      Specified Condition
      VSV for AICV (A53-1) - 1E-6
      Below 1 Ω

    3. Reconnect the VSV for AICV connector.

    4. Reinstall the engine room junction block.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT VACUUM TANK
  1. Inspect the vacuum tank (Click here).



NG
REPAIR OR REPLACE AIR CLEANER CAP
OK

REPLACE ECM (Click here)


← P1660 VSV for AICVS Circuit (Oct 2006 – May 2009)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (Oct 2006 – May 2009) →