2006-2011 Camry Aurion · Service Manual ENGINE

P0443 Evaporative Emission Control System Purge Control Valve Circuit

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through the charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signal to the VSV for EVAP so that the intake quantity of HC emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC No.
DTC Detection Condition
Trouble Area
P0443
Proper response to ECM command does not occur
(1 trip detection logic)
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM

A139242E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER

  1. A142079E01
    Disconnect the vacuum hose from the VSV for EVAP.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EVAP Control. Press the right or left button.

  1. Check if air is sucked into the port when operating the VSV for EVAP using the intelligent tester.

    Standard:
    Tester Operation
    Specified Condition
    VSV is OFF
    No air sucked

  1. Reconnect the vacuum hose.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT PURGE VSV (RESISTANCE)

  1. A127785E01
    Disconnect the C6 purge VSV connector.

  1. Measure the resistance between the terminals of the purge VSV.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    23 to 26 Ω

  1. Reconnect the purge VSV connector.



NG
REPLACE VACUUM SWITCHING VALVE
OK


3. INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

  1. A107917E04
    Disconnect the C6 purge VSV connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    Purge VSV (C6-1) - Body ground
    9 to 14 V

  1. Reconnect the purge VSV connector.



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (ECM - PURGE VSV)

  1. A107919E07
    Disconnect the C6 purge VSV connector.

  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    Purge VSV (C6-2) - PRG (C58-108)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    Purge VSV (C6-2) - PRG (C55-108)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    Purge VSV (C6-2) or PRG (C58-108) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    Purge VSV (C6-2) or PRG (C55-108) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the purge VSV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

5. CHECK HARNESS AND CONNECTOR (EFI NO. 3 FUSE - ENGINE ROOM J/B (EFI RELAY))

  1. A150646E05
    Inspect the EFI No. 3 fuse.
    1. Remove the EFI No. 3 fuse from the engine room J/B.

    2. Measure the EFI No. 3 fuse resistance.

      Standard resistance:
      Below 1 Ω

  1. Remove the engine room J/B from the engine room R/B.

  1. Disconnect the 1E engine room junction block connector.

  1. Disconnect the C6 purge VSV connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Check for open:
    Tester Connection
    Specified Condition
    Purge VSV (C6-1) - Engine room R/B (1E-6)
    Below 1 Ω

  1. Reinstall the engine room J/B.

  1. Reconnect the purge VSV connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← P0420 Catalyst System Efficiency Below Threshold (Bank 1) (+ P0430) (from Jun 2009)P0443 Evaporative Emission Control System Purge Control Valve Circuit (from Jun 2009) →