2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

U0182 Lost Communication with AFS ECU

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

The gateway ECU will store this DTC when no signals can be received from the AFS ECU while the CAN No. 2 main bus is normal.
DTC No.
DTC Detection Condition
Trouble Area
U0182
No communication from AFS ECU
  1. AFS ECU power source circuit
  2. AFS ECU
  3. AFS ECU branch wire or connector

WIRING DIAGRAM

C142764E04

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK DTC
  1. Check for DTCs.

    HINT:
    If CAN No. 2 bus DTC U1002 is output, troubleshoot for U1002 and check for malfunctions in the CAN MS main bus circuit.

    Result:
    Result
    Proceed to
    U1002 is not output
    A
    U1002 is output
    B



B
GO TO DTC CHART
A


2. CHECK CAN NO. 2 BUS WIRE (AFS ECU)
  1. Turn the engine switch off.

  1. E133227E05
    Disconnect connector A61 from the AFS ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A61-12 (MPX1) - A61-13 (MPX2)
    Engine switch off
    54 to 69 Ω



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

  1. E133227E07
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A61-22 (EIS) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Value
    A61-15 (IGSR) - Body ground
    Engine switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AFS ECU

4. CHECK FOR OPEN IN CAN NO. 2 BUS MAIN WIRE (CAN NO. 2 J/C - GATEWAY ECU)

  1. C142239E02
    Disconnect CAN No. 2 bus main wire connector E79 from the CAN No. 2 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E79-1 (CANH) - E79-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN NO. 2 BUS MAIN WIRE OR CONNECTOR (CAN NO. 2 J/C - GATEWAY ECU)
OK


5. CHECK FOR OPEN IN CAN NO. 2 BUS BRANCH WIRE (AFS ECU BRANCH WIRE)

  1. C142742E01
    Reconnect CAN No. 2 bus main wire connector E79 to the CAN No. 2 J/C.

  1. Disconnect CAN No. 2 bus branch wire connector E80 from the CAN No. 2 J/C.

  1. E133227E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E80-1 (CANH) - A61-12 (MPX1)
    Engine switch off
    Below 1 Ω
    E80-2 (CANL) - A61-13 (MPX2)



NG
REPAIR OR REPLACE CAN NO. 2 BUS BRANCH WIRE OR CONNECTOR (AFS ECU BRANCH WIRE)
OK

REPLACE CAN NO. 2 J/C


← B2326 CAN MS Bus Line Communication Malfunction (from Jun 2009)U1002 Lost Communication with Gateway Module (from Oct 2006) →