B2326 CAN MS Bus Line Communication Malfunction
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
- The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
- When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2326 |
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
- Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK CAN MS BUS WIRE |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.

- Result:
Tester Connection
Condition
Specified Value
Result
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
54 to 69 Ω
Below 54 Ω:
Short circuit between bus wires
70 Ω or higher:
Open circuit bus main wire
E58-27 (CANH) - E58-17 (E)
Engine switch off
200 Ω or higher
Below 200 Ω:
CANH ground short
E58-28 (CANL) - E58-17 (E)
Engine switch off
200 Ω or higher
Below 200 Ω:
CANL ground short
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.

- Result:
Tester Connection
Condition
Specified Value
Result
E58-27 (CANH) - E58-1 (+B)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Below 6 kΩ:
CANH +B short
E58-28 (CANL) - E58-1 (+B)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Below 6 kΩ:
CANH +B short
- Result:
Result
Proceed to
OK (w/ seat position memory)
A
OK (w/o seat position memory)
B
NG (open circuit bus main wire)
C
NG (short circuit between bus wires)
D
NG (short to ground or short to +B)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| Go to step 3 |
| 2. CHECK ECU POWER SOURCE CIRCUIT (CERTIFICATION ECU) |
Check the certification ECU power source circuit (Click here).
|
|
||||
| OK | |
| 3. REPLACE MAIN BODY ECU |
Replace the main body ECU.
| NEXT | |
| 4. RECONFIRM DTC OUTPUT |
Check the DTC.
- Result:
Result
Proceed to
B2326 not output
A
B2326 output
B
|
|
||||
| A | ||
| ||
| 5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU) |
Disconnect the certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 6. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU) |
Reconnect the certification ECU connector E58.
Disconnect the main body ECU connector E8.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (w/ Seat position memory)
B
NG (w/o Seat position memory)
C
|
|
||||
|
|
||||
| A | ||
| ||
| Go to step 3 |
| 7. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C) |
Reconnect the main body ECU connector E8.
Disconnect the CAN No. 5 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
Connected to
E81-10 (CANH) - E81-21 (CANL)
Engine switch off
108 to 132 Ω
CAN No. 3 J/C
E81-11 (CANH) - E81-22 (CANL)
Engine switch off
108 to 132 Ω
Main body ECU*1
or
CAN No. 6 J/C*2
- Result:
Result
Proceed to
OK
A
NG (to CAN No. 3 J/C)
B
NG (to Main body ECU)
C
NG (to CAN No. 6 J/C)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 8. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C - CAN NO. 3 J/C) |
Reconnect the CAN No. 5 J/C wire harness connector.
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

- HINT:
- O33 connector color: White
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | |
| 9. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO.3 J/C - CERTIFICATION ECU) |
Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

- HINT:
- O34 connector color: Gray
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 10. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 6 J/C) |
Reconnect the CAN No. 5 J/C wire harness connector.
Disconnect the CAN No. 6 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
Connected to
N40-1 (CANH) - N40-6 (CANL)
Engine switch off
108 to 132 Ω
CAN No. 5 J/C
N40-2 (CANH) - N40-7 (CANL)
Engine switch off
108 to 132 Ω
Main body ECU
- Result:
Result
Proceed to
OK
A
NG (to Main body ECU)
B
NG (to CAN No. 5 J/C)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU) |
Disconnect the certification ECU connector E58.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-28 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 12. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) |
Reconnect the certification ECU connector E58.
Disconnect the main body ECU connector E8.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Engine switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (w/ Seat position memory)
B
NG (w/o Seat position memory)
C
|
|
||||
|
|
||||
| A | ||
| ||
| Go to step 3 |
| 13. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 5 J/C) |
Reconnect main body ECU connector E8.
Disconnect the CAN No. 5 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
Connected to
E81-8 (CANH) - E81-19 (CANL)
Engine switch off
1 Ω or higher
Outer mirror control ECU
E81-9 (CANH) - E81-20 (CANL)
Engine switch off
1 Ω or higher
Seat position control ECU
E81-10 (CANH) - E81-21 (CANL)
Engine switch off
108 to 132 Ω
CAN No. 3 J/C
E81-11 (CANH) - E81-22 (CANL)
Engine switch off
108 to 132 Ω
Main body ECU*1
or
CAN No. 6 J/C*2
- Result:
Result
Proceed to
OK
A
NG (to CAN No. 3 J/C)
B
NG (to Main body ECU)
C
NG (to CAN No. 6 J/C)
D
NG (to Outer mirror control ECU or seat position control ECU)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 14. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 5 J/C - CAN NO. 3 J/C) |
Reconnect the CAN No. 5 J/C wire harness connector.
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

- HINT:
- O33 connector color: White
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| NG | |
| 15. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C - CERTIFICATION ECU) |
Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

- HINT:
- O34 connector color: Gray
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O34-1 (CANH) - O34-2 (CANL)
Engine switch off
108 to 132 Ω
|
|
||||
| OK | |
| 16. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Reconnect the CAN MS bus main wire connector O34 to the CAN No. 3 J/C.
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

- HINT:
- O32 connector color: Blue
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - O32-2 (CANL)
Engine switch off
1 Ω or higher
|
|
||||
|
|
||||
| OK | ||
| ||
| 17. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 6 J/C) |
Reconnect the CAN No. 5 J/C wire harness connector.
Disconnect the CAN No. 6 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
Connected to
N40-1 (CANH) - N40-6 (CANL)
Engine switch off
108 to 132 Ω
Main body ECU
N40-2 (CANH) - N40-7 (CANL)
Engine switch off
108 to 132 Ω
CAN No. 5 J/C
N40-3 (CANH) - N40-8 (CANL)
Engine switch off
1 Ω or higher
Mayday ECU
- Result:
Result
Proceed to
OK
A
NG (to CAN No. 5 J/C)
B
NG (to Main body ECU)
C
NG (to Mayday ECU)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 18. CHECK FOR SHORT IN CAN MS BUS WIRES (ECU) |
Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.
Recheck the short-circuited wire with the connector disconnected from the ECU.
- Standard:
- The wire is not short-circuited.
- HINT:
- If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short-circuit is suspected.
|
|
||||
| OK | ||
| ||
| 19. CHECK FOR SHORT IN CAN MS BUS WIRE (CERTIFICATION ECU) |
Measure the resistance according to the value(s) in the table below.

- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-17 (E)
Engine switch off
200 Ω or higher
E58-28 (CANL) - E58-17 (E)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
E58-27 (CANH) - E58-1 (+B)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E58-28 (CANL) - E58-1 (+B)
|
|
||||
| OK | ||
| ||
| 20. CHECK FOR SHORT IN CAN MS BUS WIRE (MAIN BODY ECU) |
Disconnect the main body ECU connector E8.

Measure the resistance according to the value(s) in the table below.

- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
E8-16 (CANP) - E10-4 (CG)
Engine switch off
200 Ω or higher
E8-15 (CANN) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
E8-16 (CANP) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
E8-15 (CANN) - E10-16 (BAT)
- Result:
Result
Proceed to
OK
A
NG (w/ Seat position memory)
B
NG (w/o Seat position memory)
C
|
|
||||
|
|
||||
| A | ||
| ||
| Go to step 3 |
| 21. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 5 J/C) |
Disconnect the CAN No. 5 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.

- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
Connected to
E81-8 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
Outer mirror control ECU
E81-19 (CANL) - E10-4 (CG)
E81-9 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
Seat position control ECU
E81-20 (CANL) - E10-4 (CG)
E81-10 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
CAN No. 3 J/C
E81-21 (CANL) - E10-4 (CG)
E81-11 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
Main body ECU*1
or
CAN No. 6 J/C
E81-22 (CANL) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
Connected to
E81-8 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Outer mirror control ECU
E81-19 (CANL) - E10-16 (BAT)
E81-9 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Seat position control ECU
E81-20 (CANL) - E10-16 (BAT)
E81-10 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
CAN No. 3 J/C
E81-21 (CANL) - E10-16 (BAT)
E81-11 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Main body ECU*1
or
CAN No. 6 J/C
E81-22 (CANL) - E10-16 (BAT)
- Result:
Result
Proceed to
OK
A
NG (to CAN CAN No. 3 J/C)
B
NG (to Main body ECU)
C
NG (to CAN No. 6 J/C)
D
NG (to Outer mirror control ECU or seat position control ECU)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 22. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 5 J/C - CAN NO. 3 J/C) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

- HINT:
- O33 connector color: White
Measure the resistance according to the value(s) in the table below.

- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O33-2 (CANL) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
O33-2 (CANL) - E10-16 (BAT)
|
|
||||
| OK | |
| 23. CHECK FOR SHORT IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 5 J/C) |
Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

- HINT:
- O34 connector color: Gray
- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O34-2 (CANL) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
O34-1 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
O34-2 (CANL) - E10-16 (BAT)
|
|
||||
| OK | |
| 24. CHECK FOR SHORT IN CAN MS BUS WIRE (CLEARANCE WARNING ECU BRANCH WIRE) |
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

- HINT:
- O32 connector color: Blue
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
O32-2 (CANL) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
O32-2 (CANL) - E10-16 (BAT)
|
|
||||
| OK | ||
| ||
| 25. CHECK FOR SHORT IN CAN MS BUS WIRE (CAN NO. 6 J/C) |
Disconnect the CAN No. 6 J/C wire harness connector.


Measure the resistance according to the value(s) in the table below.

- HINT:
- It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check CAN MS Bus Wire inspection.
- Standard resistance:
Check for CAN Bus Wire Short to Ground Tester Connection
Condition
Specified Value
Connected to
N40-1 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
Main body ECU
N40-6 (CANL) - E10-4 (CG)
N40-2 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
CAN No. 5 J/C
N40-7 (CANL) - E10-4 (CG)
E81-3 (CANH) - E10-4 (CG)
Engine switch off
200 Ω or higher
Mayday ECU
E81-8 (CANL) - E10-4 (CG)
Check for CAN Bus Wire Short to +B Tester Connection
Condition
Specified Value
Connected to
N40-1 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Main body ECU
N40-6 (CANL) - E10-16 (BAT)
N40-2 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
CAN No. 5 J/C
N40-7 (CANL) - E10-16 (BAT)
N40-3 (CANH) - E10-16 (BAT)
Cable disconnected from negative (-) battery terminal
6 kΩ or higher
Mayday ECU
N40-8 (CANL) - E10-16 (BAT)
- Result:
Result
Proceed to
OK
A
NG (to CAN CAN No. 5J/C)
B
NG (to Main body ECU)
C
NG (to Mayday ECU)
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 26. CHECK FOR SHORT IN CAN MS BUS WIRE (ECU) |
Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.
Recheck the short-circuited wire with the connector disconnected from the ECU.
- Standard:
- The wire is not short-circuited.
- HINT:
- If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.
|
|
||||
| OK | ||
| ||
