2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B1297 Clearance Sonar ECU Communication Stop

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The main body ECU will store this DTC when no signals can be received from the clearance warning ECU while the CAN MS main bus is normal.
DTC No.
DTC Detection Condition
Trouble Area
B1297
No communication from clearance warning ECU
  1. Clearance warning ECU power source circuit
  2. Clearance warning ECU
  3. Clearance warning ECU branch wire or connector

WIRING DIAGRAM

C142763E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the engine switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK DTC
  1. Check for DTCs.

    HINT:
    If CAN MS bus communication error DTC B2326 is output, troubleshoot for B2326 and check for malfunctions in the CAN MS main bus circuit (Click here).

    Result:
    Result
    Proceed to
    B2326 is not output
    A
    B2326 is output
    B



B
GO TO DTC CHART
A


2. CHECK CAN MS BUS WIRE (CLEARANCE WARNING ECU)
  1. Turn the engine switch off.

  1. C142213E03
    Disconnect connector O30 from the clearance warning ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O30-3 (R1) - O30-5 (R2)
    Engine switch off
    54 to 69 Ω



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

  1. C142213E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O30-17 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Value
    O30-15 (IG) - Body ground
    Engine switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CLEARANCE WARNING ECU

4. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 3 J/C - CLEARANCE WARNING ECU)

  1. C144988E01
    Reconnect the certification ECU connector.

  1. Disconnect the CAN No. 3 J/C connector O32.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CLEARANCE WARNING ECU)
OK


5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 3 J/C - CAN NO. 5 J/C)

  1. C144986E01
    Reconnect the CAN No. 3 J/C connector O32.

  1. Disconnect the CAN No. 3 J/C connector O33.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
OK

REPLACE CAN NO. 3 J/C


← B1276 Power Mirror Control ECU Communication Stop (from Jun 2009)B1297 Clearance Sonar ECU Communication Stop (from Jun 2009) →