2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2326 CAN MS Bus Line Communication Malfunction

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

  1. The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
  2. When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
DTC No.
DTC Detection Condition
Trouble Area
B2326
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. Open or short in CAN MS bus main wire or connector
  2. Open or short in CAN MS bus branch wire or connector
  3. Certification ECU
  4. Seat position control ECU (Front RH side)
  5. Outer mirror control ECU
  6. Clearance warning ECU
  7. Main body ECU
  8. CAN No. 3 J/C
  9. CAN No. 5 J/C

WIRING DIAGRAM

C152835E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
  3. For vehicles equipped with the mayday system, inspect the mayday system.


1. CHECK CAN MS BUS WIRE

  1. C142737E01
    Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Proceed to
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    54 to 69 Ω
    A
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    69 Ω or higher
    B
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    Below 54 Ω
    C



B
Go to step 5

C
Go to step 10
A


2. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE

  1. C144938E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 18
OK


3. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE

  1. C144938E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 23
OK


4. CHECK FOR OPEN IN CAN MS BUS BRANCH WIRE
  1. Check for an open in the branch wires of all ECUs connected to the CAN MS bus.

    1. Check the outer mirror control ECU branch wire (Click here).

    2. Check the seat position control ECU (front LH side) branch wire (Click here)

    3. Check the clearance warning ECU branch wire (Click here).

      Result:
      Result
      Proceed to
      OK
      A
      NG
      B



B
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
A

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU MAIN WIRE)

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 7
NG


6. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142197E03
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CERTIFICATION ECU
NG

REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)

7. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 3 J/C
NG


Go to step 9

8. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 5 J/C)
  1. Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142209E03
    Disconnect connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (without Seat position memory system)
    B
    NG (with Seat position memory system)
    C



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)

C
Go to step 9
A

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

9. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CAN NO. 5 J/C WIRES)
  1. Reconnect main body ECU main wire connector E8.

  1. C125896E51
    Disconnect CAN No. 5 J/C connector E81.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E81-10 (CANH) - E81-21 (CANL)
    Engine switch off
    108 to 132 Ω
    E81-11 (CANH) - E81-22 (CANL)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Defective Wire
    Proceed to
    OK
    -
    A
    NG
    Wire for main body ECU
    B
    NG
    Wire for CAN No. 3 J/C
    C



A
REPLACE CAN NO. 5 J/C

C
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
B

REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)

10. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
Go to step 15
OK


11. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU MAIN WIRE)

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 13
NG


12. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142197E03
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPLACE CERTIFICATION ECU
OK

REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)

13. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142740E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    1 MΩ or higher



OK
REPLACE NO. 3 J/C
NG


14. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)

  1. C142740E01
    Disconnect clearance warning ECU connector O30.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
OK

REPLACE NO. 3 J/C

15. CHECK FOR SHORT IN CAN MS BUS WIRES (MAIN BODY ECU MAIN WIRE)
  1. Reconnect the CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142209E03
    Disconnect the main body ECU main wire connector E8.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (without Seat position memory system)
    B
    NG (with Seat position memory system)
    C



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 3 J/C)

C
Go to step 16
A

REPLACE MAIN BODY ECU

16. CHECK FOR SHORT IN CAN MS BUS WIRES (FOR CAN NO. 5 J/C)
C142785E10
  1. Disconnect CAN No. 5 J/C connector E81.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E81-8 (CANH) - E81-19 (CANL)
    Engine switch off
    1 MΩ or higher
    E81-9 (CANH) - E81-20 (CANL)
    Engine switch off
    1 MΩ or higher
    E81-10 (CANH) - E81-21 (CANL)
    Engine switch off
    1 MΩ or higher
    E81-11 (CANH) - E81-22 (CANL)
    Engine switch off
    108 to 132 Ω

    Result:
    Result
    Defective Terminal
    Proceed to
    OK
    -
    A
    NG
    E81-10 (CANH) - E81-21 (CANL)
    B
    NG
    E81-8 (CANH) - E81-19 (CANL)
    E81-9 (CANH) - E81-20 (CANL)
    E81-11 (CANH) - E81-22 (CANL)
    C



A
REPLACE CAN NO. 5 J/C

B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
C


17. CHECK FOR SHORT IN CAN MS BUS WIRES
  1. Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.

  1. Recheck the short-circuited wire with the connector disconnected from the ECU.

    Standard:
    The wire is not short-circuited.

    HINT:
    If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short-circuit is suspected.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

18. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C145026E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 22
OK


19. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C145025E01
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 21
OK


20. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C145027E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect clearance warning ECU connector O30.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O32-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE NO. 3 J/C

21. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C145025E01
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU MAIN WIRE)
OK

REPLACE CERTIFICATION ECU

22. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU MAIN WIRE)
  1. Reconnect the CAN MS bus main wire connector O33.

  1. C142209E03
    Disconnect the main body ECU connector E8.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E8-15 (CANN) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (without Seat position memory system)
    B
    NG (with Seat position memory system)
    C



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 3 J/C)

C
Go to step 23
A

REPLACE MAIN BODY ECU

23. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 5 J/C WIRE)
C142785E10
  1. Disconnect CAN No. 5 J/C connector E81.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E81-11 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-22 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-10 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-21 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-9 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-20 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-8 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    E81-19 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher

    Result:
    Result
    Defective Wire
    Proceed to
    NG
    E81-11, E81-22, E81-9, E81-20, E81-8 or E81-19
    A
    NG
    E81-10 or E81-21
    B



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
A


24. CHECK SHORT TO +B IN CAN MS BUS WIRE
  1. Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.

  1. Recheck the short-circuited wire with the connector disconnected from the ECU.

    Standard:
    The wire is not short-circuited.

    HINT:
    If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

25. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C145026E02
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 29
OK


26. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C145025E02
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 28
OK


27. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)

  1. C145027E02
    Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect clearance warning ECU connector O30.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O32-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE NO. 3 J/C

28. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C145025E02
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU MAIN WIRE)
OK

REPLACE CERTIFICATION ECU

29. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU MAIN WIRE)
  1. Reconnect the CAN MS bus main wire connector O33.

  1. C142209E03
    Disconnect the main body ECU connector E8.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E10-4 (CG)
    Engine switch off
    6 kΩ or higher
    E8-15 (CANN) - E10-4 (CG)
    Engine switch off
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (without Seat position memory system)
    B
    NG (with Seat position memory system)
    C



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU - CAN NO. 3 J/C)

C
Go to step 30
A

REPLACE MAIN BODY ECU

30. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 5 J/C WIRE)
C142785E10
  1. Disconnect CAN No. 5 J/C connector E81.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E81-11 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-22 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-10 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-21 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-9 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-20 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-8 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E81-19 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher

    Result:
    Result
    Defective Wire
    Proceed to
    NG
    E81-11, E81-22, E81-9, E81-20, E81-8 or E81-19
    A
    NG
    E81-10 or E81-21
    B



B
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - CAN NO. 5 J/C)
A


31. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE
  1. Disconnect the connector of the ECU that is connected to the short-circuited main or branch wire from the ECU.

  1. Recheck the short-circuited wire with the connector disconnected from the ECU.

    Standard:
    The wire is not short-circuited.

    HINT:
    If the short-circuited wire returns to normal after being disconnected from the ECU, an internal ECU short circuit is suspected.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR


← B1297 Clearance Sonar ECU Communication Stop (from Jun 2009)B2326 CAN MS Bus Line Communication Malfunction (from Jun 2009) →