INSTALLATION
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL REAR COMBINATION LIGHT ASSEMBLY |
 |
- Engage the 2 clips.
Install the rear combination light assembly with the 3 screws.
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
- Connect the connectors and clamp.
| 2.
INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
|
 |
- Install the luggage compartment inner trim cover LH with the 2 clips.
| 3.
INSTALL REAR BUMPER ASSEMBLY (w/o Clearance Sonar System)
|
 |
without Rear Lower Spoiler:
- Engage each claw.
Install the rear bumper assembly with the 6 screws and 2 clips.
- Install the 2 rear bumper plates.
with Rear Lower Spoiler:
- Engage each claw.
Install the rear bumper assembly with the 6 screws.
- Install the 2 rear bumper plates.
| 4.
INSTALL REAR BUMPER ASSEMBLY (w/ Clearance Sonar System)
|
 |
without Rear Lower Spoiler:
Engage each No. 2 luggage room wire clamp to the rear bumper reinforcement sub-assembly.
- Install the grommet.
Connect the connector.
- Engage each claw.
Install the rear bumper assembly with the 6 screws and 2 clips.
- Install the 2 rear bumper plates.
with Rear Lower Spoiler:
Engage each No. 2 luggage room wire clamp to the rear bumper reinforcement sub-assembly.
- Install the grommet.
Connect the connector.
- Engage each claw.
Install the rear bumper assembly with the 6 screws.
- Install the 2 rear bumper plates.
| 5.
INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ Clearance Sonar System)
|
 |
- Install the luggage compartment inner trim cover RH with the 2 clips.
| 6.
INSTALL REAR FLOOR FINISH PLATE
|
 |
- Engage the 7 clips and install the rear floor finish plate.
| 7.
INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
|
 |
- Install the 2 No. 1 luggage compartment trim hooks with the 2 screws.
| 8.
INSTALL SPARE WHEEL COVER ASSEMBLY |
|
| 9.
INSTALL SPARE WHEEL COVER CLAMP |
|
| 10.
INSTALL LUGGAGE COMPARTMENT FLOOR MAT |
|
| 11.
INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)
|
 |
- Install the rear quarter panel mudguard sub-assembly LH with the 3 screws.
| 12.
INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler) |
 |
- HINT:
- Use the same procedure for RH and LH side.
| 13.
INSTALL REAR FLOOR BOARD (w/ Rear Lower Spoiler)
|
 |
- Install the rear floor board with the 3 nuts, 2 clips and 4 screws.
| 14.
INSTALL REAR LIGHT ASSEMBLY |
 |
- Install the rear light assembly with the 4 nuts.
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
Connect the connector and clamp.
| 15.
INSTALL LUGGAGE COMPARTMENT DOOR COVER
|
 |
- Install the luggage compartment door cover with the 13 clips.