Memory Switch Circuit
Circuit diagnosis · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The seat memory switch RH sends signals to the outer mirror control ECU via the CAN communication system to memorize a given seat position. This memory system does not use a position sensor. The seat position is detected by counting pulses that are output when the motor turns. If there is no pulse output from the motor, the motor will stop operating. The seat memory switch RH is later used to send signals to the front power seat switch RH (position control ECU) to return the seat to one of the memorized positions.The power seat memory switch RH operation can be performed only when the engine switch is on (IG) and the shift lever is in the P position.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC (CAN COMMUNICATION SYSTEM) |
Check for DTCs in the CAN communication system (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH) |
Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).
Read the DATA LIST.
Driver Seat: Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
SET SW
SET switch signal / ON or OFF
ON: SET switch is ON
OFF: SET switch is OFF
-
M1 SW
M1 switch signal / ON or OFF
ON: M1 switch is ON
OFF: M1 switch is OFF
-
M2 SW
M2 switch signal / ON or OFF
ON: M2 switch is ON
OFF: M2 switch is OFF
-
- OK:
- On the tester screen, each item changes between ON and OFF according to the above chart.
|
|
||||
| OK | ||
| ||
| 3. INSPECT SEAT MEMORY SWITCH |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Switch Position
Specified Condition
E88-1 (MRY) - E88-4 (E)
SET switch is pressed
Below 1 Ω
SET switch is not pressed
10 kΩ or higher
E88-3 (M2) - E88-4 (E)
M2 switch is pressed
Below 1 Ω
M2 switch is not pressed
10 kΩ or higher
E88-2 (M1) - E88-4 (E)
M1 switch is pressed
Below 1 Ω
M1 switch is not pressed
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH CIRCUIT) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E88-1 (MRY) - E88-4 (E)
Always
10 kΩ or higher
E88-2 (M1) - E88-4 (E)
Always
10 kΩ or higher
E88-3 (M2) - E88-4 (E)
Always
10 kΩ or higher
E88-4 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH, BODY GROUND) |
Disconnect the outer mirror control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E85-7 (M2) - E88-3 (M2)
Always
Below 1 Ω
E85-8 (M1) - E88-2 (M1)
Always
Below 1 Ω
E85-9 (MM) - E88-1 (MRY)
Always
Below 1 Ω
E85-10 (MSWE) - E88-4 (E)
Always
Below 1 Ω
E88-4 (E) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
