2006-2011 Camry Aurion · Service Manual BODY

Memory Switch Circuit

Circuit diagnosis · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The seat memory switch RH sends signals to the outer mirror control ECU via the CAN communication system to memorize a given seat position. This memory system does not use a position sensor. The seat position is detected by counting pulses that are output when the motor turns. If there is no pulse output from the motor, the motor will stop operating. The seat memory switch RH is later used to send signals to the front power seat switch RH (position control ECU) to return the seat to one of the memorized positions.
The power seat memory switch RH operation can be performed only when the engine switch is on (IG) and the shift lever is in the P position.

WIRING DIAGRAM

B126262E04

INSPECTION PROCEDURE


1. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Check for DTCs in the CAN communication system (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2. READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)

  1. E138501E01
    Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Read the DATA LIST.

    Driver Seat: 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    SET SW
    SET switch signal / ON or OFF
    ON: SET switch is ON
    OFF: SET switch is OFF
    -
    M1 SW
    M1 switch signal / ON or OFF
    ON: M1 switch is ON
    OFF: M1 switch is OFF
    -
    M2 SW
    M2 switch signal / ON or OFF
    ON: M2 switch is ON
    OFF: M2 switch is OFF
    -

    OK:
    On the tester screen, each item changes between ON and OFF according to the above chart.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3. INSPECT SEAT MEMORY SWITCH

  1. B149681E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    E88-1 (MRY) - E88-4 (E)
    SET switch is pressed
    Below 1 Ω
    SET switch is not pressed
    10 kΩ or higher
    E88-3 (M2) - E88-4 (E)
    M2 switch is pressed
    Below 1 Ω
    M2 switch is not pressed
    10 kΩ or higher
    E88-2 (M1) - E88-4 (E)
    M1 switch is pressed
    Below 1 Ω
    M1 switch is not pressed
    10 kΩ or higher



NG
REPLACE SEAT MEMORY SWITCH
OK


4. CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH CIRCUIT)

  1. B156665E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E88-1 (MRY) - E88-4 (E)
    Always
    10 kΩ or higher
    E88-2 (M1) - E88-4 (E)
    Always
    10 kΩ or higher
    E88-3 (M2) - E88-4 (E)
    Always
    10 kΩ or higher
    E88-4 (E) - Body ground
    Always
    Below 1 Ω



NG
Go to step 5
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH, BODY GROUND)

  1. B156666E01
    Disconnect the outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E85-7 (M2) - E88-3 (M2)
    Always
    Below 1 Ω
    E85-8 (M1) - E88-2 (M1)
    Always
    Below 1 Ω
    E85-9 (MM) - E88-1 (MRY)
    Always
    Below 1 Ω
    E85-10 (MSWE) - E88-4 (E)
    Always
    Below 1 Ω
    E88-4 (E) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU


← Power Seat Motor Circuit (from Oct 2006)Memory Switch Circuit (from Jun 2009) →