Engine
Engine Mechanical
ON-VEHICLE INSPECTION
1. INSPECT ENGINE COOLANT
2. INSPECT ENGINE OIL
3. INSPECT BATTERY
4. INSPECT SPARK PLUGS
5. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
(a) Remove the air cleaner filter element sub-assembly.
-
(b) Visually check there is no dirt, blockage, and/or damage to the air cleaner filter element.
HINT:
• If there is any dirt or a blockage in the air cleaner filter element, clean it with compressed air.
• If any dirt or a blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.
-
6. INSPECT VALVE LASH ADJUSTER NOISE
(a) Rev the engine several times. Check the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then repeat this procedure.
HINT:
If any defects or problems are found during the inspection above, perform lash adjuster inspection (
Click Here
)
-
7. INSPECT IGNITION TIMING
(a) Warm up the engine.
-

(b) When using the intelligent tester:
Check the ignition timing.
(1) Connect the intelligent tester to the DLC3.
(2) Enter DATA LIST mode with the intelligent tester.
Ignition timing:
7 to 24? BTDC at idle
HINT:
Refer to the intelligent tester operator's manual for help when selecting the DATA LIST.
-


(c) When not using the intelligent tester:
Check the ignition timing.
(1) Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST
09843-18040
NOTICE:
• Confirm the terminal numbers before connecting them. Connection with a wrong terminal can damage the engine.
• Turn off all electrical systems before connecting the terminals.
• Perform this inspection after the cooling fan motor is turned off.
(2) Remove the V-bank cover sub-assembly. (
Click Here
)
(3) Pull out the red lead wire harness.
(4) Connect the tester terminal of the timing light to the red lead wire as shown in the illustration.
NOTICE:
Use a timing light which can detect the first signal.
(5) Check the ignition timing at idle.
Ignition timing:
8 to 12? BTDC at idle
NOTICE:
When checking the ignition timing, the transmission should be in neutral.
HINT:
Run the engine at 1,000 to 1,300 rpm for 5 seconds, and then check the engine rpm returns to idle speed.
(6) Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
(7) Check the ignition timing at idle.
Ignition timing:
7 to 24? BTDC at idle
(8) Confirm the ignition timing moves to the advanced angle side when the engine rpm is increased.
(9) Remove the timing light.
(10) Install the V-bank cover sub-assembly. (
Click Here
)
-
8. INSPECT ENGINE IDLE SPEED

(a) Warm up the engine.
-
(b) When using the intelligent tester:
Check the idle speed.
(1) Connect the intelligent tester to the DLC3.
(2) Enter DATA LIST mode with the intelligent tester.
Idle speed:
550 to 650 rpm
NOTICE:
• When checking the idle speed, the transmission should be in neutral.
• Check the idle speed with the cooling fan off.
• Switch off all accessories and air conditioning before connecting the intelligent tester.
HINT:
Refer to the intelligent tester operator's manual for further details.
-

(c) When not using the intelligent tester:
Check the idle speed.
(1) Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.
SST
09843-18030
(2) Check the idle speed.
Idle speed:
550 to 600 rpm
-
9. INSPECT COMPRESSION
(a) Warm up and stop the engine.
-
(b) Remove the 6 ignition coils and spark plugs.
-
(c) Disconnect the fuel injector connectors.
-

(d) Check the cylinder compression pressure.
CAUTION:
Keep hands and clothing away from the v-ribbed belt while performing this operation.
(1) Insert a compression gauge into the spark plug hole.
(2) Have an assistant depress the accelerator pedal fully while cranking the engine.
(3) Measure the compression pressure.
Compression pressure:
1.4 MPa (14 kgf/cm2, 203 psi)
Minimum pressure:
0.98 MPa (10 kgf/cm2, 142 psi)
Difference between each cylinder:
0.1 MPa (1.0 kgf/cm2, 15 psi)
NOTICE:
• Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
• Check the other cylinders' compression pressure in the same way.
• This measurement must be done as quickly as possible.
(4) If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.
HINT:
• If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
• If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.
-
(e) Connect the fuel injector wire connectors.
-
(f) Install the 6 spark plugs and ignition coils.
-
10. INSPECT CO/HC
(a) Start the engine.
-
(b) Run the engine at 2,500 rpm for approximately 180 seconds.
-
(c) Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.
-
(d) Check CO/HC concentration at idle and/or 2,500 rpm.
HINT:
Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check both at idle speed and at 2,500 rpm).
If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.
(1) Check A/F sensor and heated oxygen sensor operation.
(2) See the table below for possible causes, and then inspect and repair.
-