2007 Aurion TRD · Service Manual Suspension

Front Wheel Alignment

Suspension

ADJUSTMENT
1. INSPECT TYRES ( Click Here )
2. MEASURE VEHICLE HEIGHT
(a) Bounce the vehicle up and down at the corners to stabilise the suspension. Inspect the vehicle height.
Front A - B
Rear C - D
140 mm (5.51 in.)
61 mm (2.40 in.)
Measuring points:
A:
Ground clearance of front wheel centre
B:
Ground clearance of lower suspension arm No. 2 bushing set bolt centre
C:
Ground clearance of rear wheel centre
D:
Ground clearance of strut rod set bolt centre
NOTICE:
• Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
• Perform measurement on a level surface.
• If it is necessary to go under the vehicle for measurement, confirm the parking brake is applied and the vehicle is secured with chocks.
-
3. INSPECT TOE-IN
(a) Bounce the vehicle up and down at the corners to stabilise the suspension.
-
(b) Release the parking brake and move the shift lever to the neutral position.
-
(c) Push the vehicle straight ahead approximately 5 m (16.4 ft.).
-
(d) Put tread centre marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
-
(e) Slowly push the vehicle straight ahead to cause the front wheels to rotate 180˚ using the front tyre valve as a reference point.
HINT:
Do not allow the wheels to rotate more than 180˚. If the wheels rotate more than 180˚, perform the procedure from step (c) again.
-
(f) Measure the distance between the tread centre marks on the front side of the wheels.
Toe-in
Toe-in
—
A - B:
3 +- 0.5 mm (0.12 +- 0.02 in.)
HINT:
If toe-in is not within the specified range, adjust it at the rack ends.
-
4. ADJUST TOE-IN
(a) Measure the thread lengths of the right and left rack ends.
Standard:
Difference in thread length between the right and left rack ends is 1.5 mm (0.06 in.) or less.
-
(b) Remove the rack boot set clips.
-
(c) Loosen the tie rod end lock nuts.
-
(d) Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
(1) Extend the shorter rack end if the measured toe-in deviates toward the outside.
(2) Shorten the longer rack end if the measured toe-in deviates toward the inside.
-
(e) Turn the right and left rack ends by equal amounts to adjust the toe-in.
HINT:
Try to adjust the toe-in to the centre of the specified range.
-
(f) Ensure the lengths of the right and left rack ends are the same.
-
(g) Tighten the tie rod end lock nuts.
Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)
NOTICE:
Temporarily tighten the lock nut while holding the hexagonal part of the steering rack end so the lock nut and the steering rack end do not turn together. Hold the flats on the tie rod end and tighten the lock nut.
-
(h) Place the boots on the seats and install the clips.
HINT:
Ensure the boots are not twisted.
-
5. INSPECT WHEEL ANGLE
(a) Put tread centre marks on the rear-most points of the turning radius gauge.
-
(b) Turn the steering wheel fully to the left and right and measure the turning angle.
Inside wheel
Outside wheel: reference
38˚22' +-2˚ (38.37˚ +-2˚)
33˚33' (33.55˚)
If the right and left inside wheel angles differ from the specified value, check the right and left rack end lengths.
-
6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
(a) Put the front wheel on the centre of the alignment tester.
-
(b) Remove the centre ornament.
-
(c) Set the camber-caster-king pin gauge and attachment at the centre of the axle hub or drive shaft.
-
(d) Inspect the camber, caster, and steering axis inclination.
Camber
Camber
Right-left difference
-1˚15' +30' -15' (-1.25˚ +0.5˚ -0.25˚)
20' (0.3˚) or less
Caster
Caster
Right-left difference
2˚50' +-45' (2.83˚ +-0.75˚)
30' (0.5˚) or less
Steering axis inclination
Steering axis inclination
Right-left difference
12˚20' +-45' (12.33˚ +-0.75˚)
45' (0.75˚) or less
NOTICE:
• Perform the inspection while the vehicle is unloaded.
• The maximum tolerance of the right and left difference for camber is 30' (0.5˚) and caster is 45' (0.75˚) or less.
-
(e) Remove the camber-caster-king pin gauge and attachment.
-
(f) Install the centre ornament.
-
(g) If the caster and steering axis inclination are not within the specified range after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.
-
7. ADJUST CAMBER
(a) Remove the front wheel.
-
(b) Remove the 2 nuts on the lower side of the front shock absorber.
NOTICE:
Keep the bolts inserted.
-
(c) Clean the installation surfaces of the front shock absorber and the steering knuckle.
-
(d) Temporarily install the 2 nuts (Step A).
-
(e) Fully push or pull the front axle hub in the direction of the required adjustment (Step B).
-
(f) Tighten the nuts.
Torque:
210 N*m (2,141 kgf*cm, 155 ft.*lbf)
NOTICE:
Keep the bolts from rotating when tightening the nuts.
-
(g) Install the front wheel.
Torque:
103 N*m (1,050 kgf*cm, 76 ft.*lbf)
-
(h) Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = centre of the specified range centre - measured value
Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.
HINT:
Try to adjust the camber to the centre of the specified values.
Move the axle toward (+) in step (B)
Move the axle toward (-) in step (B)
Refer to table (1)
(Move the axle toward the positive side)
Refer to table (2) (Move the axle toward the negative side)




The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.
NOTICE:
Replace the nut with a new one when replacing the bolt.
-
(i) Repeat the steps mentioned above. In step (A), replace 1 or 2 selected bolts.
HINT:
Replace one bolt at a time when replacing 2 bolts.
-