SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List.
According to the display on the tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed: Min.: 0 Km/h, Max.: 255 Km/h | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16383 rpm: | 600 to 700 rpm: Idling | - |
| Calculate Load | Calculated load by ECM: Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load: Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from mass air flow meter sub-assembly: Min.: 0 gm/sec, Max.: 655.35 gm/sec | 2 to 5 gm/sec: Idling 8 to 19 gm/sec: 2500 rpm | If value approximately 0.0 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure: Min.: 0 KPa, Max.: 255 KPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | 80 to 100°C (176 to 212°F): After warming up |
|
| Intake Air | Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature |
|
| Ambient Temperature | Ambient temperature: Min.: -40°C (-40°F), Max.: 215°C (419°F) | Actual atmospheric temperature | - |
| Engine Run Time | Engine run time: Min.: 0 s, Max.: 65535 s | Time after engine start | - |
| Initial Engine Coolant Temp | Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 119.3°C (247°F) | Close to ambient air temperature | Service data |
| Initial Intake Air Temp | Initial intake air temperature: Min.: -40°C (-40°F), Max.: 119.3°C (247°F) | Close to ambient air temperature | Service data |
| Battery Voltage | Battery voltage: Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | - |
| Accelerator Position | Accelerator pedal position: Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position No. 1: Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal released 54 to 86%: Accelerator pedal fully depressed | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position No. 2: Min.: 0%, Max.: 100% | 12 to 42%: Accelerator pedal released 66 to 98%: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Accelerator pedal released 2.6 to 4.5 V: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: Accelerator pedal released 3.4 to 4.8 V: Accelerator pedal fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1: Min.: 0 deg, Max.: 124.5 deg | - | Electronic throttle control system service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2: Min.: 0 deg Max.: 124.5 deg | - | Electronic throttle control system service data |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2 |
| ST1 | Brake pedal signal: ON or OFF | ON: Brake pedal released | - |
| System Guard | System guard: ON or OFF | - | Electronic throttle control system service data |
| Open Side Malfunction | Open side malfunction: ON or OFF | - | Electronic throttle control system service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle: ON or OFF |
| - |
| Throttle Require Position | Throttle requirement position: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*1 | Throttle sensor position: Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 5 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 5 V |
| - |
| Throttle Position Command | Throttle position command value: Min.: 0 V, Max.: 4.980 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.980 V | 0.6 to 1.4 V | Electronic throttle control system service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.980 V | 1.7 to 2.5 V | Electronic throttle control system service data |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | Electronic throttle control system service data |
| Throttle Motor DUTY | Throttle actuator: Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | Electronic throttle control system service data |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open): Min.: 0%, Max.: 255% | 0 to 40%: Idling | Electronic throttle control system service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close): Min.: 0%, Max.: 255% | 0 to 40%: Idling | Electronic throttle control system service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value): Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| +BM Voltage | +BM voltage: Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Engine switch on (IG) and system normal | Electronic throttle control system service data |
| Actuator Power Supply | Throttle actuator power supply: ON or OFF |
| - |
| Injector (Port) | Injection period: Min.: 0 μs, Max.: 65535 μs | 1200 to 2400 μs: Idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.047 ml | 0.05 to 0.15 ml: idling | Quantity of fuel injection volume for 10 times |
| Fuel Pump/Speed Status | Fuel pump/status: ON or OFF | ON: Cranking | Active Test support data |
| EVAP (Purge) VSV | Purge VSV control duty: Min.: 0%, Max.: 100% | 0 to 100%: Idling | Order signal from ECM |
| EVAP Purge Flow | Purge flow: Min.: 0%, Max.: 399.9% | 0 to 8%: Idling | Service data |
| Purge Density Learn Value | Learning value of purge density: Min.: -200, Max.: 199.993 | -40 to 10: Idling | Service data |
| EVAP Purge VSV | Purge VSV status for EVAP control: ON or OFF | - | - |
| Purge Cut VSV Duty | Purge cut VSV duty: Min.: 0%, Max.:399.9% | - | - |
| Target Air-Fuel Ratio | Air fuel ratio: Min.: 0 ,Max.: 1.999 | 0.8 to 1.2: Idling | - |
| AF Lambda B1S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| AF Lambda B2S1 | Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor |
| AFS Voltage B2S1 | Air fuel ratio sensor output voltage for bank 2 sensor 1: Min.: 0 V Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor |
| AFS Current B1S1 | Air fuel ratio sensor current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA | - | - |
| AFS Current B2S1 | Air fuel ratio sensor current for bank 2 sensor 1: Min.: -128 mA, Max.: 127.99 mA | - | - |
| A/F Heater Duty #1 | Air fuel ratio heater duty ratio for bank 1: Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| A/F Heater Duty #2 | Air fuel ratio heater duty ratio for bank 2: Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V Max.: 1.275 V | 0.1 to 0.9 V: Driving at 70 km/h (43 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor |
| O2S B2S2 | Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V Max.: 1.275 V | 0.1 to 0.9 V: Driving at 70 km/h (43 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor |
| O2 Heater B1S2 | Heated oxygen sensor heater for bank 1 sensor 2: Not Act or Active | - | - |
| O2 Heater B2S2 | Heated oxygen sensor heater for bank 2 sensor 2: Not Act or Active | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for bank 1 sensor 2: Min.: 0 A, Max.: 4.9 A | - | - |
| O2 Heater Curr Val B2S2 | Heated oxygen sensor current for bank 2 sensor 2: Min.: 0 A, Max.: 4.9 A | - | - |
| Short FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | - 20 to 20% | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | - 30 to 30% | Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value |
| Total FT #1 | Total fuel trim of bank 1 Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 0.496 | - 0.28 to 0.2: Idling | - |
| Short FT #2 | Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% | - 20 to 20% | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #2 | Long-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% | - 30 to 30% | Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value |
| Total FT #2 | Total fuel trim of bank 1 Average value for fuel trim system of bank 2: Min.: -0.5, Max.: 0.496 | - 0.28 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (bank 1): OL or CL or OLDrive or OLFault or CL Fault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (bank 2): OL or CL or OLDrive or OLFault or CL Fault | CL: Idling after warming up |
|
| IGN Advance | Ignition timing advance for No. 1 cylinder: Min.: -64 deg, Max.: 63.5 deg | BTDC 9.5 to 24.5 deg: Idling | - |
| Knock Feedback Value | Feedback value of knocking: Min.: -1024 CA, Max.: 1023.9 CA | -22 to 0 CA: Driving at 70 km/h (43 mph) | Service data |
| Knock Correct Learn Value | Correction learning value of knocking: Min.: -1024 CA, Max.: 1023.9 CA | 0 to 22 CA: Driving at 70 km/h (43 mph) | Service data |
| ACIS VSV | Intake air control valve assembly for acoustic control induction system status: ON or OFF | ON: Open OFF: Closed | - |
| AICV VSV | Vacuum switching valve for air intake control system status: ON or OFF | - | - |
| VVT Control Status #1 | VVT control (bank 1) status: ON or OFF | - | - |
| VVT Control Status #2 | VVT control (bank 2) status: ON or OFF | - | - |
| VVT Aim Angle #1*2 | VVT aim angle (bank 1): Min.: 0%, Max.: 399.9% | 0%: Idling | VVT duty signal value during intrusive operation |
| VVT Change Angle #1*2 | VVT change angle (bank 1): Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation |
| VVT OCV Duty #1*2 | VVT camshaft timing oil control valve assembly operation duty: Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation |
| VVT Aim Angle #2*2 | VVT aim angle (bank 2): Min.: 0%, Max.: 399.9% | - | VVT duty signal value during intrusive operation |
| VVT Change Angle #2*2 | VVT change angle (bank 2): Min.: 0 DegFR, Max.: 699.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation |
| VVT OCV Duty #2*2 | VVT camshaft timing oil control valve assembly (bank 2) operation duty: Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation |
| VVT Ex Hold Lrn Val #1*2 | VVT exhaust hold duty ratio learning value (bank 1): Min.: 0%, Max.: 399.9% | 10 to 50%: Idling | - |
| VVT Ex Chg Angle #1*2 | VVT exhaust change angle (bank 1): Min.: 0 DegFR, Max.: 699.9 DegFR | 0 to 5 DegFR: Idling | - |
| VVT Ex OCV Duty #1*2 | VVT exhaust camshaft timing oil control valve assembly duty (bank 1): Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| VVT Ex Hold Lrn Val #2*2 | VVT exhaust hold duty ratio learning value (bank 2): Min.: 0%, Max.: 399.9% | 10 to 50%: Idling | - |
| VVT Ex Chg Angle #2*2 | VVT exhaust change angle (bank 2): Min.: 0 DegFR, Max.: 699.9 DegFR | 0 to 5 DegFR: Idling | - |
| VVT Ex OCV Duty #2*2 | VVT exhaust camshaft timing oil control valve assembly duty (bank 1): Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| VN Turbo Type | Variable nozzle turbo type: Not Avl or Commo or Vacuum or CAN Com | Not Avl | - |
| Catalyst Temp B1S1 | Catalyst temperature (bank 1, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B2S1 | Catalyst temperature (bank 2, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (bank 1, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B2S2 | Catalyst temperature (bank 2, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Starter Signal | Starter signal: Open or Close | Open: Starter signal ON Close: Starter signal OFF | - |
| Starter Control | Starter switch signal: ON or OFF | - | - |
| Power Steering Signal Record | Power steering signal: ON or OFF | ON: Power steering operation | - |
| Starter Relay | Starter relay: ON or OFF | ON: Cranking | - |
| ACC Relay | ACC relay ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | Park/neutral position switch assembly status: ON or OFF | ON: P or N position | - |
| Stop Light Switch | Stop light switch assembly: ON or OFF | ON: Brake pedal depressed | - |
| A/C Signal | A/C signal: ON or OFF | ON: A/C on | - |
| Idle Up Signal | Idle up signal: ON or OFF | - | - |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF |
| - |
| Fuel Cut Condition | Fuel-cut condition: ON or OFF | ON: Any fuel cut operation executed | - |
| Check Mode | Check mode: ON or OFF | ON: Check mode on | Click here
|
| SPD Test Result | Check mode result for vehicle speed sensor: Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor: Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (bank 1): Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (bank 2): Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (bank 2): Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (bank 1): Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor: Not Avl or Avail | - | Comprehensive Component Monitor |
| Fuel System Monitor | Fuel system monitor: Not Avl or Avail | - | Fuel System Monitor |
| Misfire Monitor | Misfire monitor: Not Avl or Avail | - | Misfire Monitor |
| EGR/VVT Monitor | EGR/VVT monitor: Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor: Compl or Incmpl | - | - |
| O2S (A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor: Not Avl or Avail | - | - |
| O2S (A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor: Compl or Incmpl | - | - |
| O2S (A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor: Not Avl or Avail | - | - |
| O2S (A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor: Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor: Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor: Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor: Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor: Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor: Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor: Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor: Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor: Compl or Incmpl | - | - |
| TC Terminal | TC terminal status: ON or OFF | - | - |
| # Codes (Include History) | #Codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status: ON or OFF | ON: MIL on | - |
| MIL ON Run Distance | MIL on run distance: Min.: 0 Km, Max.: 65535 Km | Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL turned on: Min.: 0 min, Max.: 65535 min | Equivalent to running time after MIL turned on | - |
| Time after DTC Cleared | Time after DTC cleared: Min.: 0 min, Max.: 65535 min | Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared: Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| Dist Batt Cable Disconnect | Distance from battery cable disconnect: Min.: 0 Km, Max.: 65535 Km | - | - |
| OBD Requirements | OBD requirement | E-OBD | - |
| Number of Emission DTC | Emission related DTCs: Min.: 0, Max.: 127 | - | Number of emission related DTCs |
| TC and TE1 | TC and TE1 terminals of DLC3: ON or OFF | - | Active Test support data |
| Ignition Trig. Count | Ignition counter: Min.: 0, Max.: 65535 | 0 to 600 | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #5 Misfire Count | Misfire count of cylinder 5: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #6 Misfire Count | Misfire count of cylinder 6: Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | All cylinders misfire count: Min.: 0, Max.: 255 | 0 to 35 | - |
| Misfire RPM | Engine speed for first misfire range: Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring: Min.: -128%, Max.: 127% | - 100 to 99.22% | Misfire detecting margin |
| Catalyst OT MF F/C | Catalyst overheat misfire prevention F/C availability: Not Avl or Avail |
| Service data |
| Cat OT MF F/C History | Catalyst overheat misfire prevention F/C history: ON or OFF | ON: Fuel cut operation history exists | Service data |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 (if certain level of misfire malfunction is detected): ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 (if certain level of misfire malfunction is detected): ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 (if certain level of misfire malfunction is detected): ON to OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 (if certain level of misfire malfunction is detected): ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 (if certain level of misfire malfunction is detected): ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 (if certain level of misfire malfunction is detected): ON or OFF | ON: Fuel cut is operating | - |
| ACM Inhibit | Duty vacuum switching valve for active control engine mount: ON or OFF | OFF: Idling | - |
| ACM | Duty vacuum switching valve for active control engine mount duty control: Min.: 0%, Max.: 255% | - | Active Test support data |
| Electric Fan Motor | Electric fan motor: ON or OFF | ON: Electric fan motor operating | - |
| Idle Fuel Cut Prohibit | Idle fuel cut prohibit: ON or OFF | - | - |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operating | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2500 rpm |
| FC TAU | Fuel cut TAU (Fuel cut during very light load): ON or OFF | ON: Fuel cut operating | Fuel cut being performed under very light load to prevent incomplete engine combustion |
| Communication with ECT | Status of communication with the TCM: Comm or No Comm | - | - |
| Electrical Load Signal 1 | Electrical load signal: ON or OFF | - | - |
| Model Code | Model code | - | Identifying model code: GSV40# |
| Engine Type | Engine type | - | Identifying engine type: 2GRFE |
| Cylinder Number | Cylinder number | - | Identifies cylinder number: 6 |
| Transmission Type | Transmission type | - | Identifying transmission type: ECT 6th |
| Destination | Destination | - | Identifies destination: W |
| Model Year | Model year | - | Identifies model year: 200# |
| System Identification | System identification | - | Identifying engine system: Gasoline (gasoline engine) |
| Engine Speed of Cyl #1 | Engine speed for cylinder 1: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #2 | Engine speed for cylinder 2: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #3 | Engine speed for cylinder 3: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #4 | Engine speed for cylinder 4: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #5 | Engine speed for cylinder 5: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #6 | Engine speed for cylinder 6: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Av Engine Speed of All Cyl | Engine speed for all cylinders: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test 51199 rpm: Active Test not performed |
| Received MIL from ECT | Received MIL from TCM: ON or OFF | MIL illuminate instruction ON signal from TCM: ON | - |
| Shift Position Sig from ECT | Received shift position signal from TCM: | Actual shift position | - |
| A/T Oil Temp from ECT | Received ATF temperature sensor value from TCM: Min.: -40°C (-40°F), Max.: 215°C (419°F) |
| If the value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is open or shorted |
| SPD (NO) | Output shaft speed: Min.: 0 rpm, Max.: 12750 rpm | 0 rpm: Vehicle stopped | - |
| ECT Lock up | Lock up: ON or OFF | ON: Lock up operating | - |
| Shift SW Status (P Range) | Park/neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (R Range) | Park/neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Sports Shift Up SW | Sport shift up switch status: ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status: ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status: ON or OFF |
| - |
| Shift SW Status (D Range) | Park/neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on the intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| ACTIVE TEST |
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test.
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5 and 24.8 % |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | Lower by -12.5 % or increase by 25 % |
|
| Active the VSV for Intake Control | Activate Intake air control valve assembly for acoustic control induction system | ON/OFF |
|
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | Only purge VSV is commanded during this test |
| Control the Fuel Pump / Speed | Activate fuel pump (C/OPN Relay) | ON/OFF | Test possible when following conditions met:
|
| Control the ACM Inhibit | Control the active control engine mount inhibit | ON/OFF | - |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel out operation during misfire | ON: Fuel cut is prohibited | Confirm that the vehicle is stopped and engine speed is 3000 rpm or less |
| Control the Electric Cooling Fan | Control electric cooling fan | ON/OFF | Test possible when following conditions met:
|
| Active the Starter Relay | Starter | ON/OFF | - |
| Activate the ACC Cut Relay | Active ACC Cut relay | ON/OFF | Test possible when following condition met:
|
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Open/Close | Test possible when following conditions met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Open/Close | Test possible when following conditions met:
|
| Control the VVT Linear (Bank 1) | Control the camshaft timing oil control valve assembly for intake camshaft (bank 1) | -128 to 127% This value added to present camshaft timing oil control valve assembly control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn on and off the camshaft timing oil control valve assembly for intake camshaft (bank 1) | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control the camshaft timing oil control valve assembly for intake camshaft (bank 2) | -128 to 127% This value added to present camshaft timing oil control valve assembly control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 2) | Turn on and off the camshaft timing oil control valve assembly for intake camshaft (bank 2) | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control the camshaft timing oil control valve assembly for exhaust camshaft (bank 1) | -128 to 127% This value added to present camshaft timing oil control valve assembly control duty 100%: Maximum retard -100%: Maximum advance |
|
| Control the VVT Exhaust Linear (Bank 2) | Control the camshaft timing oil control valve assembly for exhaust camshaft (bank 2) | -128 to 127% This value added to present camshaft timing oil control valve assembly control duty 100%: Maximum retard -100%: Maximum advance |
|
| Activate the VSV for AICS | Activate vacuum switching valve for air intake control | ON/OFF | - |
| Control the Cylinder #1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #5 Fuel Cut | Cylinder #5 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #6 Fuel Cut | Cylinder #6 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control All Cylinders Fuel Cut | All cylinders fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Check the Cylinder Compression* | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stopped in all cylinders. |