DTC P0115 Engine Coolant Temperature Circuit Malfunction |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC No. | Proceed to | DTC Detection Condition | Trouble Area |
| P0115 | Step 1 | Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 | Step 4 | Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0118 | Step 2 | Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Select the following menu items: Powertrain / Engine / Data List / Coolant Temp.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0115 | A |
| P0117 | B |
| P0118 | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the tester.
| Temperature Displayed | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| Between 80°C and 97°C (176°F and 207°F) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR OPEN IN SENSOR) |
![]() |
Confirm good connection of the sensor.
Disconnect the C4 engine coolant temperature (ECT) sensor connector.
Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
![]() |
Disconnect the C4 ECT sensor connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| THW (C58-79) - C4-2 | Below 1 Ω |
| ETHW (C58-78) - C4-1 | Below 1 Ω |
| Tester Connection | Specified Condition |
| THW (C55-79) - C4-2 | Below 1 Ω |
| ETHW (C55-78) - C4-1 | Below 1 Ω |
Reconnect the ECM connector.
Reconnect the ECT connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR) |
![]() |
Disconnect the C4 ECT sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
![]() |
Disconnect the C4 ECT sensor connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| THW (C58-79) or C4-2 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| THW (C55-79) or C4-2 - Body ground | 10 kΩ or higher |
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||