DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | Heated Oxygen (HO2) sensor heater current is less than 0.3 A (1 trip detection logic) |
|
| P0038 P0058 | Heated Oxygen (HO2) sensor heater current is more than 3.5 A (1 trip detection logic) |
|
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C52 heated oxygen sensor connector (Bank 1 Sensor 2) or C51 heated oxygen sensor connector (Bank 2 Sensor 2).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HT1B (1) - +B (2) | 20°C (68°F) | 11 to 16 Ω |
| HT1B (1) - E2 (4) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HT2B (1) - +B (2) | 20°C (68°F) | 11 to 16 Ω |
| HT2B (1) - E2 (4) | Always | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR) |
![]() |
Disconnect the C52 heated oxygen sensor connector (Bank 1 Sensor 2) or C51 heated oxygen sensor connector (Bank 2 Sensor 2).
Turn the ignition switch to the ON position.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| +B (C52-2) - Body ground | 9 to 11 V |
| +B (C51-2) - Body ground | 9 to 11 V |
Reconnect the HO2 sensor connector.
|
| ||||
| NG | |
| 3.INSPECT FUSE (EFI NO. 3) |
![]() |
Remove the EFI No. 3 fuse from the engine room R/B.
Measure the EFI No. 3 fuse resistance.
Reinstall the EFI No. 3 fuse.
|
| ||||
| OK | |
| 4.INSPECT ENGINE ROOM JUNCTION BLOCK |
![]() |
Remove the engine room junction block from the engine room R/B.
Inspect the EFI relay.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-12 - 1E-6 | 10 kΩ or higher |
| 1E-12 - 1E-6 | Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-10) |
Reinstall the engine room junction block.
|
| ||||
| OK | |
| 5.INSPECT FUSE (EFI MAIN) |
![]() |
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse.
Reinstall the EFI MAIN fuse.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - EFI RELAY) |
![]() |
Disconnect the C52 or C51 HO2 sensor connector.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C52-2) - 1E-6 (Engine room R/B) | Below 1 Ω |
| +B (C51-2) - 1E-6 (Engine room R/B) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C52-2) or 1E-6 (Engine room R/B) - Body ground | 10 kΩ or higher |
| +B (C51-2) or 1E-6 (Engine room R/B) - Body ground | 10 kΩ or higher |
Reinstall the engine room junction block.
Reconnect the HO2 sensor connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM) |
![]() |
Disconnect the C52 heated oxygen sensor connector (Bank 1 Sensor 2) or C51 heated oxygen sensor connector (Bank 2 Sensor 2).
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Terminal Connection | Specified Condition |
| +B (C52-2) - Body ground | 9 to 14 V |
| +B (C51-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal Connection | Specified Condition |
| HT1B (C52-1) - HT1B (C58-48) | Below 1 Ω |
| OX1B (C52-3) - OX1B (C58-88) | Below 1 Ω |
| E2 (C52-4) - EX1B (C58-65) | Below 1 Ω |
| HT2B (C51-1) - HT2B (C58-47) | Below 1 Ω |
| OX2B (C51-3) - OX2B (C58-87) | Below 1 Ω |
| E2 (C51-4) - EX2B (C58-64) | Below 1 Ω |
| Terminal Connection | Specified Condition |
| HT1B (C52-1) - HT1B (C55-48) | Below 1 Ω |
| OX1B (C52-3) - OX1B (C55-88) | Below 1 Ω |
| E2 (C52-4) - EX1B (C55-65) | Below 1 Ω |
| HT2B (C51-1) - HT2B (C55-47) | Below 1 Ω |
| OX2B (C51-3) - OX2B (C55-87) | Below 1 Ω |
| E2 (C51-4) - EX2B (C55-64) | Below 1 Ω |
| Terminal Connection | Specified Condition |
| HT1B (C52-1) or HT1B (C58-48) - Body ground | 10 kΩ or higher |
| OX1B (C52-3) - OX1B (C58-88) - Body ground | 10 kΩ or higher |
| E2 (C52-4) or EX1B (C58-65) - Body ground | 10 kΩ or higher |
| HT2B (C51-1) or HT2B (C58-47) - Body ground | 10 kΩ or higher |
| OX2B (C51-3) or OX2B (C58-87) - Body ground | 10 kΩ or higher |
| E2 (C51-4) or EX2B (C58-64) - Body ground | 10 kΩ or higher |
| Terminal Connection | Specified Condition |
| HT1B (C52-1) or HT1B (C55-48) - Body ground | 10 kΩ or higher |
| OX1B (C52-3) - OX1B (C55-88) - Body ground | 10 kΩ or higher |
| E2 (C52-4) or EX1B (C55-65) - Body ground | 10 kΩ or higher |
| HT2B (C51-1) or HT2B (C55-47) - Body ground | 10 kΩ or higher |
| OX2B (C51-3) or OX2B (C55-87) - Body ground | 10 kΩ or higher |
| E2 (C51-4) or EX2B (C55-64) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 2 minutes.
Select the following menu items: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed To |
| No output | A |
| P0037, P0038, P0057 and/or P0058 | B |
|
| ||||
| A | ||
| ||