DTC P0335 Crankshaft Position Sensor "A" Circuit |
DTC P0339 Crankshaft Position Sensor "A" Circuit Intermittent |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0335 | When one of the following conditions is met (1 trip detection logic) :
|
|
| P0339 | Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1 trip detection logic) (a) Engine speed 1000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
|
![]() |
| ECM Terminal Name | CH1: Between G2+ and G2- CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |

| 1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
![]() |
Disconnect the crankshaft position sensor connector.
Measure the resistance between terminals 1 and 2.
| Tester Connection | Specified Condition |
| 1 - 2 | 1,150 to 1,450 Ω (at 20°C (68°F)) |
| *1 | Component without harness connected (Crankshaft Position Sensor) |
Reconnect the crankshaft position sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C20-1 - C24-122 (NE+) | Always | Below 1 Ω |
| C20-2 - C24-121 (NE-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C20-1 or C24-122 (NE+) - Body ground | Always | 10 kΩ or higher |
| C20-2 or C24-121 (NE-) - Body ground | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() |
Check the crankshaft position sensor installation.
|
| ||||
| OK | |
| 5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Inspect the teeth of the crankshaft position sensor plate.
|
| ||||
| OK | |
| 6.REPLACE CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and run it at idle for 20 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0335 and/or P0339 are output | B |
|
| ||||
| A | ||
| ||