DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the transmission fluid pressure. (2-trip detection logic) |
|
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P2714" is output | A |
| "P2714" and other DTCs | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) |
Turn the ignition switch off.
Lift the vehicle up.
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the intelligent tester to the DLC3.
Start the engine.
Warm up the ATF (Automatic Transmission Fluid).
Measure the line pressure when the engine is idling.
Turn on the tester.
Enter the following items: Powertrain / ECT / Active Test / Activate the Solenoid (SLT)".
Follow the instructions on the tester and perform the Active Test.
Measure the line pressure with SST.
| Item | Test Details |
| Activate the Solenoid (SLT)* | [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFTING TEST) |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn on the tester.
Enter the following items: "Powertrain / ECT / Active Test".
Follow the instructions on the tester and read the Powertrain / ECT / Active Test.
| Item | Test Details | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition]
| It is possible to check the operation of the shift solenoid valves. |
Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM gear shift command and the actual gear position.
| Actuator gear position under malfunction | TCM gear shift command | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1
| N*1
| N*1
| N*1
| 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1
| N*1
| ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1
| ||
| Shift solenoid SL4 | Stuck ON*3
| 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1
| 6th | ||
| Shift solenoid SLT | Stuck ON | N*2
| N*2
| N*2
| N*2
| N*2
| N*2
| E |
| Stuck OFF*3
| 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| E | |
| 4.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
|
| ||||
| OK | ||
| ||