CAN COMMUNICATION SYSTEM (for LHD) > Short to B+ in CAN Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. |
|


| 1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
Cable disconnect from the battery negative (-) terminal.
![]() |
Disconnect the DLC3 branch wire connector (E62) from the No. 1 CAN J/C "B" side (without earth terminal).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E10-14 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Reconnect the DLC3 branch wire connector (E62) to the No. 1 CAN J/C "B" side (without earth terminal).
|
| ||||
| OK | |
| 2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN J/C SIDE) |
![]() |
Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).
![]() |
Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E10-14 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| NG | |
| 3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE |
![]() |
Disconnect connectors from the No. 1 CAN J/C one at a time.
Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.


| No. 1 CAN J/C connectors ("A" side, with earth terminal) | Connector Color | Wire Color (CAN-H) | Wire Color (CAN-L) |
| Center Airbag Sensor (E45) | Black | B | W |
| No. 1 CAN J/C connectors ("A" side, with earth terminal) | Connector Color | Wire Color (CAN-H) | Wire Color (CAN-L) |
| Yaw Rate Sensor (E46)* | Blue | B | W |
| Steering Angle Sensor (E63)* | Brown | B | W |
| Combination Meter (E43) | White | B | W |
| Main Body ECU (E44) | Black | B | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or more) when a connector is disconnected from the No. 1 CAN J/C. (There is a short to B+ in one of the areas that relate to one or more of the disconnected bus wires.) | A |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the No. 1 CAN J/C. (There is a short to B+ in the CAN main bus wires between the No. 1 CAN J/C and No. 2 CAN J/C.) | B |
When there is a short to B+ in one or more of the bus wires that connect to an ECU (or sensor):
Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to B+). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to B+ in one bus wire only.
|
| ||||
| A | |
| 4.RECONNECT CONNECTOR |
Reconnect the connector of the bus wire that is shorted to B+ to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 6 kΩ or more when it was disconnected).
| NEXT | |
| 5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE |
![]() |
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to B+ is connected. (Click here)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E10-14 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE |
![]() |
Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C A side (with earth terminal).
Disconnect the No. 2 CAN J/C connector (A40).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E10-14 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| NG | |
| 7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN J/C) |
Disconnect the No. 2 CAN J/C connector (E41).

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Connected to |
| E41-1 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier |
| E41-7 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E41-4 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 CAN J/C |
| E41-10 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E41-5 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Navigation receiver assembly |
| E41-11 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (to No. 1 CAN J/C main wire) | B |
| NG (to ECU or sensor wire) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN J/C) |
Disconnect the No. 2 CAN J/C connector (A40).

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value | Connected to |
| A40-1 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| A40-7 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| A40-2 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Skid control ECU |
| A40-10 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECU, SENSOR) |
Reconnect the No. 1 and No. 2 CAN J/C connectors.
![]() |
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to B+ is connected. (Click here)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E10-14 (CANL) - E10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||