SFI SYSTEM > Cranking Holding Function Circuit |

| 1.CHECK CRANKING |
When starting the engine, check whether the starter motor starts.
|
| ||||
| NG | |
| 2.READ VALUE USING INTELLIGENT TESTER (STA SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal. Read the values.
Check the result when the engine switch is turned on (IG) and when the engine is started.
| Display (Starter Signal) | Condition |
| OFF | Engine switch on (IG) |
| ON | Engine start |
|
| ||||
| NG | |
| 3.INSPECT ECM (STSW VOLTAGE) |
![]() |
Disconnect the A24 (RHD) or A55 (LHD) ECM Connector.
Measure the voltage between the terminal of the ECM connector and body ground while cranking the engine.
| Tester Connection | Specified Condition |
| STSW (A24-14) - Body ground | 11 to 14 V |
| Tester Connection | Specified Condition |
| STSW (A55-14) - Body ground | 11 to 14 V |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.INSPECT ECM (STAR VOLTAGE) |
![]() |
Remove the ST CUT relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground while cranking the engine.
| Tester Connection | Specified Condition |
| ST CUT relay (3) - Body ground | 11 to 14 V |
Reinstall the ST CUT relay.
|
| ||||
| OK | |
| 5.INSPECT ST CUT RELAY |
![]() |
Remove the ST CUT relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied between terminals 1 and 2) |
Reinstall the ST CUT relay.
|
| ||||
| OK | |
| 6.INSPECT PARK/NEUTRAL SWITCH ASSEMBLY |
![]() |
Inspect the Park/Neutral Position (PNP) switch.
Disconnect the C1 switch connector.
Measure the resistance according to the value(s) in the table below.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 4 - 5 | Below 1 Ω |
| N | 4 - 5 | Below 1 Ω |
Reconnect the PNP switch connector.
|
| ||||
| OK | ||
| ||
| 7.INSPECT STARTER RELAY |
![]() |
Remove the ST relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied between terminals 1 and 2) |
Reinstall the ST relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY) |
![]() |
Disconnect the C1 park/neutral position switch connector.
Remove the ST relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| C1-9 - ST relay terminal (1) | Below 1 Ω |
| Tester Connection | Specified Condition |
| C1-9 or ST relay terminal (1) - Body ground | 10 kΩ or higher |
Reinstall the ST relay.
|
| ||||
| OK | |
| 9.INSPECT ENGINE ROOM RELAY BLOCK (STARTER RELAY VOLTAGE) |
![]() |
Remove the ST relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground.
| Tester Connection | Specified Condition |
| ST relay (5) - Body ground | 11 to 14 V |
|
| ||||
| OK | |
| 10.INSPECT STARTER ASSEMBLY |
Inspect the starter assembly (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |
![]() |
Disconnect the E9 main body ECU connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| STSW (E9-4) - STSW (A24-14) | Below 1 Ω |
| Tester Connection | Specified Condition |
| STSW (E9-4) - STSW (A55-14) | Below 1 Ω |
| Tester Connection | Specified Condition |
| STSW (E9-4) or STSW (A24-14) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| STSW (E9-4) or STSW (A55-14) - Body ground | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||