ENGINE UNIT > INSPECTION |
| 1. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Turn the roller by hand to check that it turns smoothly.
| 2. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
Place the lash adjuster into a container filled with engine oil.
![]() |
Insert the SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove the SST. Then try to quickly and firmly press the plunger with a finger.
| 3. INSPECT CAMSHAFT |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Using a micrometer, measure the cam lobe height.
| Item | Specification |
| Intake camshaft | 44.316 to 44.416 mm (1.7447 to 1.7487 in.) |
| Exhaust camshaft | 44.262 to 44.362 mm (1.7426 to 1.7465 in.) |
| Item | Specification |
| Intake camshaft | 44.166 mm (1.7388 in.) |
| Exhaust camshaft | 44.112 mm (1.7367 in.) |
![]() |
Using a micrometer, measure the journal diameter.
| Item | Specification |
| No. 1 journal | 35.946 to 35.960 mm (1.4152 to 1.4157 in.) |
| Other journals | 25.959 to 25. 975 mm (1.0220 to 1.0226 in.) |
| 4. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing gear and camshaft together by aligning the key groove and straight pin.
Lightly press the gear against the camshaft, and turn the gear. Push further at the position where the pin enters the groove.
Check that there is no clearance between the gear's flange and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing gear fixed.
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path and the retard side path on the opposite side to the hole of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 broken paths.
![]() |
Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.
Check for smooth rotation.
Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear is locked at the most retarded position.
![]() |
Remove the flange bolt and camshaft timing gear.
| 5. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing exhaust gear and camshaft together by aligning the key groove and straight pin.
Lightly press the gear against the camshaft, and turn the gear. Push further at the position where the pin enters the groove.
Check that there is no clearance between the gear's flange and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing exhaust gear fixed.
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear is locked.
![]() |
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 broken paths (the advance side path and the retard side path).
![]() |
Make sure that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear is locked at the most advanced position.
![]() |
Remove the flange bolt and camshaft timing exhaust gear.
| 6. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using vernier calipers, measure the minimum diameter of the elongated thread at the measuring point.
| 7. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.
Using vernier calipers, measure the length of 15 links.
| 8. INSPECT NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.
Using vernier calipers, measure the length of 15 links.
| 9. INSPECT CRANKSHAFT TIMING SPROCKET |
Wrap the chain around the sprocket.
![]() |
Using vernier calipers, measure the sprocket diameter with the chain.
| 10. INSPECT IDLE SPROCKET ASSEMBLY |
Wrap the chain around the sprocket.
![]() |
Using vernier calipers, measure the sprocket diameter with the chain.
| 11. INSPECT IDLE GEAR SHAFT OIL CLEARANCE |
![]() |
Using a micrometer, measure the idle gear shaft diameter.
![]() |
Using a caliper gauge, measure the inside diameter of the idle gear.
Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.
| 12. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
If necessary, replace the chain tensioner assembly.
| 13. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 14. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 15. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the worn depth of the chain tensioner slipper.
| 16. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the chain vibration damper.
| 17. INSPECT NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the chain vibration damper.
| 18. INSPECT CYLINDER HEAD ASSEMBLY |
![]() |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder block and manifolds.
| Item | Warpage |
| Cylinder head lower | 0.05 mm (0.0020 in.) |
| Intake | 0.08 mm (0.0031 in.) |
| Exhaust | 0.08 mm (0.0031 in.) |
| Item | Warpage |
| Cylinder head lower | 0.10 mm (0.0039 in.) |
| Intake | 0.10 mm (0.0039 in.) |
| Exhaust | 0.10 mm (0.0039 in.) |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head assembly.
| 19. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using vernier calipers, measure the valve head margin thickness.
![]() |
Using vernier calipers, measure the valve's overall length.
| 20. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using vernier calipers, measure the valve head margin thickness.
![]() |
Using vernier calipers, measure the valve's overall length.
| 21. INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure.
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.1 and 1.5 mm (0.043 and 0.059 in.).
| 22. INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure.
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.1 and 1.5 mm (0.043 and 0.059 in.).
| 23. REPAIR INTAKE VALVE SEAT |
![]() |
Using a 45° cutter, resurface the valve seat so that the valve seat width is more than the specification.
![]() |
Using 30° and 60° cutters, correct the valve seat so that the valve contacts the entire circumference of the seat. The contact should be in the center of the valve seat, and the valve seat width should be maintained within the specified range around the entire circumference of the seat.
Handrub the valve and valve seat with an abrasive compound.
Check the valve seating position.
| 24. REPAIR EXHAUST VALVE SEAT |
![]() |
Using a 45° cutter, resurface the valve seat so that the valve seat width is more than the specification.
![]() |
Using 30° and 75° cutters, correct the valve seat so that the valve contacts the entire circumference of the seat. The contact should be in the center of the valve seat, and the valve seat width should be maintained within the specified range around the entire circumference of the seat.
Handrub the valve and valve seat with an abrasive compound.
Check the valve seating position.
| 25. INSPECT COMPRESSION SPRING |
![]() |
Using vernier calipers, measure the free length of the compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 26. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Clearance |
| Intake | 0.025 to 0.060 mm (0.0010 to 0.0024 in.) |
| Exhaust | 0.030 to 0.065 mm (0.0012 to 0.0026 in.) |
| Item | Clearance |
| Intake | 0.08 mm (0.0032 in.) |
| Exhaust | 0.10 mm (0.0039 in.) |
| 27. INSPECT CAMSHAFT THRUST CLEARANCE |
Inspect the RH bank camshaft thrust clearance.
Install the RH bank camshafts (Click here).
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
Inspect the LH bank camshaft thrust clearance.
Install the LH bank camshafts (Click here).
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 28. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps (Click here).
Remove the bearing caps (Click here).
![]() |
Measure the Plastigage at its widest point.
| Item | Oil Clearance |
| No. 1 journal | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) |
| Other journals | 0.025 to 0.062 mm (0.00098 to 0.0024 in.) |
| Item | Oil Clearance |
| No. 1 journal | 0.10 mm (0.0039 in.) |
| Other journals | 0.09 mm (0.0035 in.) |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps (Click here).
Remove the bearing caps (Click here).
![]() |
Measure the Plastigage at its widest point.
| Item | Oil Clearance |
| No. 1 journal | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) |
| Other journals | 0.025 to 0.062 mm (0.00098 to 0.0024 in.) |
| Item | Oil Clearance |
| No. 1 journal | 0.10 mm (0.0039 in.) |
| Other journals | 0.09 mm (0.0035 in.) |
| 29. INSPECT CONNECTING ROD THRUST CLEARANCE |
Install the connecting rod cap (Click here).
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 30. INSPECT CONNECTING ROD OIL CLEARANCE |
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
![]() |
Lay a strip of Plastigage on the crank pin.
![]() |
Check that the front mark of the connecting rod cap is facing forward.
Install the connecting rod cap (Click here).
Remove the 2 bolts and connecting rod cap (Click here).
![]() |
Measure the Plastigage at its widest point.
| Mark | Diameter |
| 1 | 56.000 to 56.006 mm (2.2047 to 2.2050 in.) |
| 2 | 56.007 to 56.012 mm (2.2050 to 2.2052 in.) |
| 3 | 56.013 to 56.018 mm (2.2052 to 2.2054 in.) |
| 4 | 56.019 to 56.024 mm (2.2055 to 2.2057 in.) |
| Mark | Thickness |
| 1 | 1.481 to 1.484 mm (0.0583 to 0.0584 in.) |
| 2 | 1.484 to 1.487 mm (0.0584 to 0.0585 in.) |
| 3 | 1.487 to 1.490 mm (0.0585 to 0.0587 in.) |
| 4 | 1.490 to 1.493 mm (0.0587 to 0.0588 in.) |
| 31. INSPECT CRANKSHAFT THRUST CLEARANCE |
Install the main bearing cap (Click here).
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 32. INSPECT CYLINDER BLOCK FOR WARPAGE |
![]() |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.
| 33. INSPECT CYLINDER BORE |
![]() |
Visually check the cylinder for vertical scratches.
If deep scratches are present, rebore all the 6 cylinders. If necessary, replace the cylinder block.
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
| 34. INSPECT PISTON SUB-ASSEMBLY WITH PIN |
![]() |
Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston end is as specified.
| 35. INSPECT PISTON OIL CLEARANCE |
Measure the cylinder bore diameter in the thrust directions.
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 36. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Clearance |
| No. 1 | 0.020 to 0.070 mm (0.0008 to 0.0028 in.) |
| No. 2 | 0.020 to 0.060 mm (0.0008 to 0.0024 in.) |
| Oil | 0.070 to 0.150 mm (0.0028 to 0.0059 in.) |
| 37. INSPECT PISTON RING END GAP |
Insert the piston ring into the cylinder bore.
![]() |
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| Item | End Gap |
| No. 1 | 0.25 to 0.35 mm (0.0098 to 0.0138 in.) |
| No. 2 | 0.50 to 0.60 mm (0.0197 to 0.0236 in.) |
| Oil | 0.10 to 0.40 mm (0.0039 to 0.0157 in.) |
| Item | End Gap |
| No. 1 | 0.50 mm (0.0197 in.) |
| No. 2 | 0.85 mm (0.0335 in.) |
| Oil | 0.60 mm (0.0236 in.) |
| 38. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Mark | Diameter |
| A | 22.001 to 22.004 mm (0.8662 to 0.8663 in.) |
| B | 22.004 to 22.007 mm (0.8663 to 0.8664 in.) |
| C | 22.007 to 22.010 mm (0.8664 to 0.8665 in.) |
![]() |
Using a micrometer, measure the piston pin diameter.
| Mark | Diameter |
| A | 21.997 to 22.000 mm (0.8660 to 0.8661 in.) |
| B | 22.000 to 22.003 mm (0.8661 to 0.8663 in.) |
| C | 22.003 to 22.006 mm (0.8663 to 0.8664 in.) |
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bushing.
| Mark | Diameter |
| A | 22.005 to 22.008 mm (0.8663 to 0.8665 in.) |
| B | 22.009 to 22.011 mm (0.8665 to 0.8666 in.) |
| C | 22.012 to 22.014 mm (0.8666 to 0.8667 in.) |
![]() |
Subtract the piston pin diameter measurement from the bushing inside diameter measurement.
| 39. INSPECT CONNECTING ROD |
![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for out-of-alignment.
![]() |
Check for twist.
| 40. INSPECT CONNECTING ROD BOLT |
![]() |
Using vernier calipers, measure the tension portion diameter of the bolt.
| 41. INSPECT CRANKSHAFT |
Inspect for circle runout.
Clean the crank journal.
Place the crankshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
Inspect the main journals.
![]() |
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown in the illustration.
Inspect the crank pin.
![]() |
Using a micrometer, measure the diameter of each crank pin.
Check each crank pin for taper and out-of-round as shown in the illustration.
| 42. INSPECT CRANKSHAFT OIL CLEARANCE |
Check the crank journal and bearing for pitting and scratches.
Install the crankshaft bearing (Click here).
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
Examine the front marks and numbers and install the bearing caps on the cylinder block.
Install the main bearing cap (Click here).
Remove the main bearing caps (Click here).
![]() |
Measure the Plastigage at its widest point.
![]() |
If replacing a bearing, replace it with one having the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for the appropriate bearing number. There are 5 sizes of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.
| Cylinder block + Crankshaft | 0 - 5 | 6 - 11 | 12 - 17 | 18 - 23 | 24 - 28 |
| Bearing to be used | "1" | "2" | "3" | "4" | "5" |
| Mark | Diameter |
| "00" | 60.999 to 61.000 mm (2.4015 to 2.4016 in.) |
| "01" | 60.998 to 60.999 mm (2.4015 to 2.4015 in.) |
| "02" | 60.997 to 60.998 mm (2.4015 to 2.4015 in.) |
| "03" | 60.996 to 60.997 mm (2.4014 to 2.4015 in.) |
| "04" | 60.995 to 60.996 mm (2.4014 to 2.4014 in.) |
| "05" | 60.994 to 60.995 mm (2.4013 to 2.4014 in.) |
| "06" | 60.993 to 60.994 mm (2.4013 to 2.4013 in.) |
| "07" | 60.992 to 60.993 mm (2.4013 to 2.4013 in.) |
| "08" | 60.991 to 60.992 mm (2.4012 to 2.4013 in.) |
| "09" | 60.990 to 60.991 mm (2.4012 to 2.4012 in.) |
| "10" | 60.989 to 60.990 mm (2.4011 to 2.4012 in.) |
| "11" | 60.988 to 60.989 mm (2.4011 to 2.4011 in.) |
| Mark | Thickness |
| "1" | 2.500 to 2.503 mm (0.0984 to 0.0985 in.) |
| "2" | 2.503 to 2.506 mm (0.0985 to 0.0987 in.) |
| "3" | 2.506 to 2.509 mm (0.0987 to 0.0988 in.) |
| "4" | 2.509 to 2.512 mm (0.0988 to 0.0989 in.) |
| "5" | 2.512 to 2.515 mm (0.0989 to 0.0990 in.) |
| Mark | Thickness |
| "1" | 2.478 to 2.481 mm (0.0976 to 0.0977 in.) |
| "2" | 2.481 to 2.484 mm (0.0977 to 0.0978 in.) |
| "3" | 2.484 to 2.487 mm (0.0978 to 0.0979 in.) |
| "4" | 2.487 to 2.490 mm (0.0979 to 0.0980 in.) |
| "5" | 2.490 to 2.493 mm (0.0980 to 0.0981 in.) |
| Mark | Thickness |
| "1" | 2.478 to 2.481 mm (0.0976 to 0.0977 in.) |
| "2" | 2.481 to 2.484 mm (0.0977 to 0.0978 in.) |
| "3" | 2.484 to 2.487 mm (0.0978 to 0.0979 in.) |
| "4" | 2.487 to 2.490 mm (0.0979 to 0.0980 in.) |
| "5" | 2.490 to 2.493 mm (0.0980 to 0.0981 in.) |
| Mark | Thickness |
| "1" | 2.500 to 2.503 mm (0.0984 to 0.0985 in.) |
| "2" | 2.503 to 2.506 mm (0.0985 to 0.0987 in.) |
| "3" | 2.506 to 2.509 mm (0.0987 to 0.0988 in.) |
| "4" | 2.509 to 2.512 mm (0.0988 to 0.0989 in.) |
| "5" | 2.512 to 2.515 mm (0.0989 to 0.0990 in.) |
| 43. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using vernier calipers, measure the minimum diameter of the compressed thread at the measuring point.