ENTRY AND START SYSTEM > SYSTEM DESCRIPTION |
| ENTRY AND START SYSTEM DESCRIPTION |
In addition to conventional mechanical key and wireless door lock control functions, the entry and start system enables door locking/unlocking, steering lock releasing, engine starting and luggage compartment door opening without operating the key. The only requirement is that the key is in the user's possession.
| DETECTION AREA |

| Actuation Area | Detail |
| Interior | The interior detection area of the indoor electrical key oscillators (for front and rear floor) is formed when the driver door is opened or closed, when the engine switch is pushed, when a warning is activated, or when the lock switch on the front door outside handle assembly. |
| Exterior | The exterior detection area formed by the door electrical key oscillators (for driver and front passenger side) and outside electrical key oscillator (for luggage compartment is approximately 0.7 to 1.0 m (2.30 to 3.28 ft.) from the front door outside handle assembly of the front doors, or the center of the rear bumper. |
| Around Front Door | The exterior detection area of the door electrical key oscillator (for driver or front passenger side) is formed by transmitting a request signal every 0.25 seconds while the engine switch is off and each door is locked. In this way it detects the proximity of a key. When locking the door using the lock switch on the front door outside handle assembly, the detection area is formed when the lock switch is touched. |
| Around Luggage Compartment | The exterior detection area of the outside electrical key oscillator (for luggage compartment) is formed by when the luggage compartment door opener outer switch is on. |
Precautions for the entire system:
| FUNCTION OF MAIN COMPONENTS |
| Component | Function |
| Key | Consists of mechanical key, transmitter for wireless door lock control and transceiver for entry and start system |
| Certification ECU (Smart key ECU assembly) |
|
| ID Code Box (Immobiliser Code ECU) | Receives steering unlock or engine immobiliser unset signals from certification ECU (smart key ECU assembly), certifies them, and transmits unset signals to steering lock ECU (steering lock actuator assembly) or ECM |
| Main Body ECU (Instrument Panel Junction Block Assembly) |
|
| Door Outside Handle Assembly (for driver, front passenger side) (touch sensor) | Detects when person touches inside of outside handle |
| Door Outside Handle Assembly (for driver, front passenger side) (lock switch) | Transmits door lock request signals to certification ECU (smart key ECU assembly) |
| Door Electrical Key Oscillator (for driver, front passenger side) | Receives request signal from certification ECU (smart key ECU assembly), and forms detection area around each door |
| Indoor Electrical Key Oscillator (for front floor, rear floor) | Receives request signal from certification ECU (smart key ECU assembly), and forms detection area in vehicle interior |
| Indoor Electrical Key Oscillator (for luggage compartment) | Receives request signal from certification ECU (smart key ECU assembly), and forms detection area in luggage compartment |
| Outside Electrical Key Oscillator (for luggage compartment) | Receives request signal from certification ECU (smart key ECU assembly), and forms detection area around luggage compartment door |
| Door Control Receiver |
|
| Electrical Key Antenna* | Receives ID code from key and transmits it to entry door control receiver |
| Luggage Compartment Door Opener Outer Switch | Transmits luggage compartment door open request signal to certification ECU (smart key ECU assembly) |
| Stop Light Switch | Outputs state of brake pedal to main body ECU (instrument panel junction block assembly) |
| When certification ECU (smart key ECU assembly) detects human errors such as those below, it warns driver by sounding wireless door lock buzzer assembly and displaying information in accordance with request signal from ECU
|
| CONSTRUCTION AND OPERATION |
Key
The key consists of a mechanical key, a transmitter function for the wireless door lock control and a transceiver for the entry and start system.

Oscillator (each door electrical key oscillator, indoor electrical key oscillator (for front and rear floor), indoor electrical key oscillator (for luggage compartment), outside electrical key oscillator (for luggage compartment))
Each oscillator transmits the request signal received from the certification ECU (smart key ECU assembly), and forms a key detection area to detect the presence of a key. The detection area formed by each door electrical key oscillator and outside electrical key oscillator (for luggage compartment) is approximately 0.7 to 1.0 m (2.30 to 3.28 ft.) from the outside handle of each door or the center of the rear bumper.
| ENTRY FUNCTION OPERATION |
The entry and start system has the following functions:
| Function | Outline |
| Mechanical Key | Operation is the same as conventional mechanical key. |
| Wireless Door Lock Control | This function remotely locks and unlocks all doors or luggage compartment. Operation is the same as wireless door lock control system. However, the receiver in certification ECU (smart key ECU assembly) uses entry door control receiver to control locking and unlocking. |
| Entry Illumination | When person carrying key enters detection area, door will enter unlock standby mode and front map light. |
| Entry Unlock | When key is located in detection area of door electrical key oscillator, door will unlock by touching inside of door outside handle assembly. |
| Entry Lock | When key is located in detection area of door electrical key oscillator and engine switch is off, door can be locked by pressing lock switch on door outside handle assembly. |
| Entry Luggage Compartment Open | When key is in detection area of outside electrical key oscillator (for luggage compartment), luggage compartment opens by pressing luggage compartment open switch. |
| Key Lock-in Prevention |
|
| Warning | When any of situations below occur, entry and start system causes certification ECU (smart key ECU assembly) to sound buzzer in combination meter and wireless door lock buzzer, and illuminate information in order to alert driver:
|
| Battery Saving | If key is constantly located within actuation area of door electrical key oscillator, system maintains periodic communication with key. Therefore, if vehicle remains parked in that state for a long time, key battery and vehicle battery could be drained. For this reason, vehicle has controls for saving battery power. |
| Key Cancel (Click here) | Following key functions can be cancelled by performing certain operations:
|
| Key Code Registration | The total number of keys that can be registered is seven. This function enables the registration (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly). |
| WIRELESS DOOR LOCK AND UNLOCK AND LUGGAGE COMPARTMENT OPEN FUNCTION |
| ENTRY UNLOCK FUNCTION |
The detection area is formed by communication between a door electrical key oscillator and certification ECU (smart key ECU assembly) when the door is locked in order to detect access of the person carrying the key.
When the person carrying the key enters the detection area around the vehicle, the matching of the ID codes for a door electrical key oscillator and key will automatically be performed. After the matching is completed, the door will enter unlock standby mode.
In unlock standby mode, the antenna built into the outside handle starts sensing. If the outside handle is held (the backside of the handle is touched), the door unlock operation will be performed. At this time, the hazard warning lights blink twice and the wireless door lock buzzer sounds twice.
If any door is not opened after a door unlock operation, all doors will automatically lock after 30 seconds.
| ENTRY LOCK FUNCTION |
After leaving the vehicle carrying the key, push the lock switch on an outside handle when all the doors are closed.
The certification ECU (smart key ECU assembly) determines whether the key is located inside or outside the cabin based on the information from a door electrical key oscillator and indoor electrical key oscillator. Then matching of the ID codes is performed.
When the matching result shows that the ID codes of the key and indoor electrical key oscillator do not match and the ID codes of the key and door electrical key oscillator match, the door lock function will operate. At this time, the hazard warning lights blink once and the wireless door lock buzzer sounds once.
If the key is located inside the cabin, the door lock function will not operate and the alarm buzzer (beep sound) will sound for 2 seconds.
| ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION |
| PREVENTION OF KEY CONFINEMENT FUNCTION |
If locking the door through keyless operation (moving the lock knob to the lock position and then closing the door) with the key in the cabin is attempted, the system determines that the key is located in the cabin and unlocks the door.
If the luggage compartment is closed with the key in it, the alarm will sound and the luggage compartment can be opened only when all the doors are locked in order to prevent key confinement in the vehicle.
| ENTRY ILLUMINATION FUNCTION |
| ENTRY POWER WINDOW FUNCTION (REMOTE FUNCTION) (DOOR WINDOW AND SLIDING ROOF CLOSE OPERATION ONLY) |
Pressing the front door outside handle assembly (lock switch) for 3 seconds or more operates the door window close operation of all of the windows and the sliding roof close operation.
If the entry power window function is operating and the front door outside handle assembly (lock switch) is released, the entry power window operation will stop.
| WARNING FUNCTION |
General
When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter and the wireless door lock buzzer, and illuminate the combination meter multi-information display in order to alert the driver.
| Warning Function Operation Condition | Situation |
| Exit warning if shift lever is not in P and power source mode is not off. | A |
| Exit warning if shift lever is in P and power source mode is not off. | B |
| An occupant leaves with the key. | C |
| The engine switch is operated while the key is outside the detection area. | D |
| Entry lock is operated while the key is inside the cabin. | E |
| The key battery is weak. | F |
| The key reminder sounds. | G |
| A door is ajar. | H |
| The key is left in the luggage compartment. | I |
| Steering lock does not release. | J |
| The steering lock mechanism is malfunctioning. | K |
| The main body ECU (instrument panel junction block assembly) is malfunctioning. | L |
| An engine start method is displayed. | M |
| Emergency operation support (a backup function is used). | N |
Situation A
There are 2 patterns for situation A.
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Continuous sound |
Combination Meter
| Warning: Information below is displayed on the combination meter:
|
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
| Possible Effects without Warning | Sudden vehicle start, vehicle theft, vehicle roll-away |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Continuous sound |
Combination Meter
| Warning: Information is displayed alternately on the combination meter:
|
Combination Meter
| Flashes |
| Wireless Door Lock Buzzer Assembly | Warning: Continuous sound The warning is stopped when one of the following conditions is met:
|
Situation B
There are 2 patterns for situation B.
| Possible Effects without Warning | Vehicle theft, Engine cannot be restarted, Discharged battery |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed on the combination meter:
|
Combination Meter
| Flashes |
| Wireless Door Lock Buzzer Assembly | Warning: Sounds 3 times |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
|
| Possible Effects without Warning | Vehicle theft, Discharged battery |
| Warning Condition | The certification ECU (smart key ECU assembly) gives warning when all of the following conditions are met:
|
Combination Meter
| - |
Combination Meter
| Warning: Information is displayed on the combination meter:
|
| Wireless Door Lock Buzzer Assembly | Warning: Sounds for 60 seconds |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
Situation C
When the engine is left running, a passenger leaves the vehicle while holding the key.
In this situation, the following control is performed:
| Possible Effects without Warning | Engine cannot be restarted |
| Warning Condition | The certification ECU (smart key ECU assembly) gives warning when all of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed on the combination meter:
|
| Wireless Door Lock Buzzer Assembly | Warning: Sounds 3 times |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
|
Situation D
When the key is not in the cabin or the key battery is dead, the driver attempts to start the engine or turn the engine switch on (IG).
In this situation, the following control is performed:
| Possible Effects without Warning | Confuses the user |
| Warning Condition | The warning is activated when both of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed on the combination meter for 10 seconds (disappears after 10 seconds):
|
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when the following condition is met:
|
Situation E
The lock switch on the door outside handle assembly is pressed to perform entry lock with the key left in the cabin.
In this situation, the following control is performed:
| Possible Effects without Warning | Vehicle theft |
| Warning Condition | The certification ECU (smart key ECU assembly) gives warning when all of the following conditions are met:
|
Combination Meter
| - |
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | Warning: Sounds for 2 seconds |
| Engine Switch Indicator Light | - |
Situation F
The vehicle is driven using a key that has a low battery.
In this situation, the following control is performed:
| Possible Effects without Warning | Entry and start system does not function. |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed on the combination meter: Displayed for 10 seconds (disappears after 10 seconds)
|
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
Situation G
There are 2 patterns for situation G.
| Possible Effects without Warning | Vehicle theft |
| Warning Condition | The warning is activated when either of the following conditions is met:
|
Combination Meter
| Continues to sound at short and even intervals |
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
Situation H
The lock switch on the door outside handle assembly is pressed to perform entry lock with a door open. In this situation, the following control is performed:
| Possible Effects without Warning | Vehicle theft |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| - |
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | Warning: Sounds for 10 seconds |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
Situation I
The luggage compartment door is closed with the key left in the luggage compartment. In this situation, the following control is performed:
| Possible Effects without Warning | Key confinement |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| - |
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | Sounds for 2 seconds |
Situation J
The steering lock cannot be released. In this situation, the following control is performed:
| Possible Effects without Warning | Steering usability function |
| Warning Condition | The steering lock cannot be released, thus the engine is prevented from starting. |
Combination Meter
| - |
Combination Meter
| Warning: Information is displayed on the combination meter: Displayed for 15 seconds (and then automatically turned off)
|
Combination Meter
| Flashes |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | The green indicator blinks at 1-second intervals (goes off automatically in 15 seconds). |
| Warning Stop Condition | The engine switch is pressed while the steering wheel is turned left and right, and the steering lock is successfully released. |
Situation K
A malfunction of the steering lock ECU (steering lock actuator assembly) is detected. In this situation, the following control is performed:
| Possible Effects without Warning | Malfunction detection |
| Warning Condition | A malfunction of the steering lock ECU (steering lock actuator assembly) is detected. |
Combination Meter
| - |
Combination Meter
| Warning: Information is displayed on the combination meter:
|
Combination Meter
| Flashes |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | The amber indicator blinks at 2-second intervals. |
| Warning Stop Condition | The steering lock ECU (steering lock actuator assembly) returns to normal. |
Situation L
A malfunction of the main body ECU (instrument panel junction block assembly) is detected. In this situation, the following control is performed:
| Possible Effects without Warning | Malfunction detection |
| Warning Condition | A malfunction in the main body ECU (instrument panel junction block assembly) is detected. |
Combination Meter
| - |
Combination Meter
| - |
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | The amber indicator blinks at 2-second intervals. |
| Warning Stop Condition | The main body ECU (instrument panel junction block assembly) returns to normal. |
Situation M
There are 2 patterns for situation M.
| Possible Effects without Warning | Usability function |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| - |
Combination Meter
| Warning: Information is displayed alternately on the combination meter:
|
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
| Possible Effects without Warning | Usability function |
| Warning Condition | The warning is activated when the following condition is met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed alternately on the combination meter:
|
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
Situation N
There are 2 patterns for situation N.
| Possible Effects without Warning | Usability function |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed alternately on the combination meter:
|
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
| Possible Effects without Warning | Usability function |
| Warning Condition | The warning is activated when all of the following conditions are met:
|
Combination Meter
| Warning: Sounds once |
Combination Meter
| Warning: Information is displayed alternately on the combination meter:
|
Combination Meter
| - |
| Wireless Door Lock Buzzer Assembly | - |
| Engine Switch Indicator Light | - |
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
|
| BATTERY SAVING |
Vehicle Battery Saving Function
In the entry and start system, signals are emitted outside the vehicle at a prescribed interval (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are carried out:
| Condition | Control |
Both conditions below are met for 5 days:
| Signal transmission interval is extended from 0.25 to 0.75 seconds. |
Both conditions below are met for 14 days:
| The entry and start system is automatically deactivated. |
Key Battery and Vehicle Battery Saving Function
In the entry and start system, if the key is constantly located within the vehicle exterior detection area of the doors, the system maintains periodic communication with the key. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the entry and start system automatically becomes deactivated.
Reinstatement Conditions