STEERING LOCK SYSTEM > DIAGNOSIS SYSTEM |
| DESCRIPTION |
DIAGNOSTIC SYSTEM
When troubleshooting a vehicle with a diagnostic system, the only difference from the usual troubleshooting procedure is connecting the intelligent tester to the vehicle and reading various data output from the vehicle's steering lock ECU (steering lock actuator assembly).
The steering lock ECU (steering lock actuator assembly) records DTCs when the ECU detects a malfunction in itself or in system circuits.
To check the DTCs, connect the intelligent tester to the DLC3 on the vehicle. The intelligent tester enables the DTCs to be cleared, the indicators to be activated, and the DATA LIST to be checked.
The steering lock ECU (steering lock actuator assembly) diagnosis information cannot be read directly from the steering lock ECU (steering lock actuator assembly) by the intelligent tester. The diagnosis information from the steering lock ECU (steering lock actuator assembly) is transmitted to the intelligent tester via the certification ECU to the intelligent tester using the Controller Area Network (CAN).
| CHECK DLC3 |
![]() |
The certification ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.
| Symbols (Terminal No.) | Terminal Description | Condition | Specified Condition |
| SIL (7) - SG (5) | Bus "+" line | During transmission | Pulse generation |
| CG (4) - Body ground | Chassis ground | Always | Below 1 Ω |
| SG (5) - Body ground | Signal ground | Always | Below 1 Ω |
| BAT (16) - Body ground | Battery positive | Always | 11 to 14 V |
| CANH (6) - CANL (14) | CAN bus line | Engine switch off* | 54 to 69 Ω |
| CANH (6) - CG (4) | HIGH-level CAN bus line | Engine switch off* | 200 Ω or higher |
| CANL (14) - CG (4) | LOW-level CAN bus line | Engine switch off* | 200 Ω or higher |
| CANH (6) - BAT (16) | HIGH-level CAN bus line | Engine switch off* | 6 kΩ or higher |
| CANL (14) - BAT (16) | LOW-level CAN bus line | Engine switch off* | 6 kΩ or higher |
Connect the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the intelligent tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the intelligent tester.
| WARNING FUNCTION OF ENGINE SWITCH INDICATOR |
![]() |
The steering lock ECU (steering lock actuator assembly) blinks the LED indicator of the engine switch when any of the following problems occurs in the system:
| Detection Item | Indicator Light Blink Pattern | Indication Status | Countermeasure |
| Steering lock is still not released |
| The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column). | Push the engine switch while turning the steering wheel left or right. |
| Malfunction in entry and start system |
|
| Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here). |
| WARNING FUNCTION OF COMBINATION METER |
The steering lock ECU (steering lock actuator assembly) displays a warning on the combination meter when any of the following problems occurs in the system.
| Detection Item | Display | Indication Status | Countermeasure |
| Steering lock is still not released | "S/T IS NOT UNLOCKED"
| The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column). | Push the engine switch while turning the steering wheel left or right. |
| Malfunction in entry and start system | "CHECK S/T LOCK"
|
| Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here). |