Home › ENGINE · 2GR-FE › STARTING › ENTRY AND START SYSTEM

DTC    B2278    Engine Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
  1. Engine switch
  2. Main body ECU
  3. Wire harness or connector

WIRING DIAGRAM


B112447E07


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (START SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Check the Data List for proper functioning of the start switch.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    St SW 1
    Start Switch 1/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    St SW 2
    Start Switch 2/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    ON (engine switch on (IG)) and OFF (engine switch off) appear on the screen.



NG
Go to step 3
OK


2.CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off

      HINT:
      1. If power mode does not change to ON (IG and ACC) (Click here).
      2. If power mode does not change to ON (IG) (Click here).
      3. If power mode does not change to ON (ACC) (Click here).



NG
GO TO OTHER PROBLEM
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT ENGINE SWITCH


  1. Remove the engine switch (Click here).


    A109252E01

  1. Disconnect the switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

    HINT:
    This switch is a momentary type switch.



NG
REPLACE ENGINE SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)


  1. Disconnect the E7 ECU connector.


    B137980E01

  1. Disconnect the E52 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-7 (SS1) - E7-17 (SSW1)
    Always
    Below 1 Ω
    E52-2 (SS2) - E7-16 (SSW2)
    Always
    Below 1 Ω
    E52-5 (GND) - Body ground
    Always
    Below 1 Ω
    E52-7 (SS1) or E7-17 (SSW1) - Body ground
    Always
    10 kΩ or higher
    E52-2 (SS2) or E7-16 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU