FUEL SYSTEM > PRECAUTION |
| 1.PRECAUTION |
Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.
Do not smoke or work near fire when handling the fuel system.
Keep gasoline away from rubber or leather parts.
| 2.DISCHARGE FUEL SYSTEM PRESSURE |
Remove the rear seat cushion assembly.
![]() |
Remove the rear floor service hole cover.
Disconnect the fuel pump connector.
Start the engine.
After the engine stops, turn the ignition switch off.
Crank the engine again. Check that the engine does not start.
Remove the fuel tank cap to discharge pressure from the fuel tank.
Disconnect the cable from the negative (-) battery terminal.
Reconnect the fuel pump connector.
Install the rear floor service hole cover.
Install the rear seat.
| 3.FUEL SYSTEM |
When disconnecting a high fuel pressure line, a large amount of gasoline will spill out, so perform the following procedure:
Discharge the fuel system pressure (step 2).
Disconnect the fuel pump tube .
Drain the fuel that remains inside the fuel pump tube.
![]() |
Cover the disconnected pipe and connector with a plastic bag to prevent damage and contamination.
Put a container under the connection part.
![]() |
Observe the following precautions when removing and installing the fuel injectors:
Never reuse an O-ring.
When placing a new O-ring on the injector, do not damage the O-ring.
Coat a new O-ring with gasoline before installing it.
![]() |
Install the injector to the delivery pipe and cylinder head, as shown in the illustration.
![]() |
Perform the following procedure when disconnecting a fuel delivery pipe (metallic type):
![]() |
Remove the No. 2 fuel pipe clamp.
![]() |
Find the metallic connector of the fuel tube assembly.
Assemble SST to the connection as shown in the illustration.
Turn the SST, align the retainers inside the connector with the SST chamfered parts and insert SST into the connector.
Slide the SST and the connector together towards the fuel tube assembly.
Perform the following procedure when connecting a fuel tube connector (metallic type):
Check if there is any damage or foreign objects on the connecting part of the pipe.
Match the axis of the connector with the axis of the pipe, and push into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.
![]() |
After finishing the connection, check if the pipe and the connector are securely connected by pulling on them.
Check for fuel leaks.
![]() |
Install a new No. 2 fuel pipe clamp.
Perform the following procedure when disconnecting a fuel tube connectors (Quick Type A):
![]() |
Remove the No. 1 fuel pipe clamp from the tube connector.
Check that there is no dirt or other foreign objects on the pipe and around the connector before disconnecting them. Clean them if necessary.
![]() |
Disconnect the connector from the pipe by hand.
When the connector and the pipe are stuck, push in and pull on the connector to release it. Pull the connector out of the pipe carefully.
Check that there is no dirt or other foreign objects on the sealing surface of the disconnected pipe. Clean it away if necessary.
![]() |
Cover the disconnected pipe and connector with a plastic bag to prevent damage and contamination.
Perform the following procedure when connecting a fuel tube connector (Quick Type A):
Check if there is any damage or foreign objects on the connecting parts of the pipes.
Line up the two parts of the pipes to be connected, and push them together until the connector makes a "click" sound. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
![]() |
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
Check for fuel leaks.
![]() |
Perform the following procedure when disconnecting a fuel tube connector (Quick type B):
Before disconnecting the connector, clean off any dirt that may be present.
Pinch the tabs of the fuel tube retainer to disengage the 2 claws. Push the retainer down as shown in the illustration.
![]() |
If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.
If there is any dirt or any other foreign objects on the sealing surfaces of the disconnected pipes, clean them if necessary.
![]() |
Cover the disconnected pipe and connector with a plastic bag to prevent damage and contamination.
Perform the following procedure when connecting a fuel tube connector (Quick Type B):
![]() |
Line up the two parts of the pipes to be connected, and fully push the fuel tube connector and pipe together until they are fully seated. Next, push the retainer into the connector until its claws lock. If the pipe is difficult to push in to the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
Check for fuel leaks.
Observe the following precautions when handling a nylon tube:
| 4.CHECK FOR FUEL LEAKS |
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs (Click here).