Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1810/53    Short in Driver Side Squib 2nd Step Circuit

DTC    B1811/53    Open in Driver Side Squib 2nd Step Circuit

DTC    B1812/53    Short to GND in Driver Side Squib 2nd Step Circuit

DTC    B1813/53    Short to B+ in Driver Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable, and the steering pad.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1810/53
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during primary check.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1811/53
  1. The center airbag sensor assembly receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1812/53
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1813/53
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM


H001451E45


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)


    C114814E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert straight the SST into the terminals of the connector.

SST
09843-18060  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812, B1813, or 53 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813, and 53 may be output at this time, but they are not related to this check.



OK
REPLACE STEERING PAD (Click here)
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE (Click here)
OK


3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT


    C114815E01
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      D2+ - Body ground
      ignition switch ON
      Below 1 V
      D2- - Body ground
      ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - D2-
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - Body ground
      Always
      1 MΩ or higher
      D2- - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - D2-
      Always
      1 MΩ or higher



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C114816E01
  1. Connect the connectors to the steering pad and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812, B1813, or 53 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813, and 53 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE


    C114807E16
  1. Check for a short to B+ in the circuit.

    1. Restore the released activation prevention mechanism of connector B to the original condition.

    2. Disconnect the instrument panel wire connector from the spiral cable.

    3. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    4. Turn the ignition switch to the ON position.

    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      E16-4 (D2+) - Body ground
      Ignition switch ON
      Below 1 V
      E16-3 (D2-) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E16-4 (D2+) - E16-3 (D2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E16-4 (D2+) - Body ground
      Always
      1 MΩ or higher
      E16-3 (D2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E16-4 (D2+) - E16-3 (D2-)
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK


6.CHECK SPIRAL CABLE


    C114817E01
  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      D2+ - Body ground
      Ignition switch ON
      Below 1 V
      D2- - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch to the LOCK position.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - D2-
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - Body ground
      Always
      1 MΩ or higher
      D2- - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D2+ - D2-
      Always
      1 MΩ or higher



NG
REPLACE SPIRAL CABLE (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)